Identify the species oxidized, the species reduced, the oxidizing agent and the reducing agent in the following electron transfer reaction. 3BR2 + 2Cr-6Br" + 2Cr3+ species oxidized species reduced oxidizing agent reducing agent to As the reaction proceeds, electrons are transferred from Submit Answer Retry Entire Group 7 more group attempts remaining

Identify the species oxidized, the species reduced, the oxidizing agent and the reducing agent in the following electron transfer reaction. 3BR2 + 2Cr-6Br" + 2Cr3+ species oxidized species reduced oxidizing agent reducing agent to As the reaction proceeds, electrons are transferred from Submit Answer Retry Entire Group 7 more group attempts remaining

Chemistry: Matter and Change

1st Edition

ISBN:9780078746376

Author:Dinah Zike, Laurel Dingrando, Nicholas Hainen, Cheryl Wistrom

Publisher:Dinah Zike, Laurel Dingrando, Nicholas Hainen, Cheryl Wistrom

Chapter20: Electrochemistry

Section: Chapter Questions

Problem 46A

See similar textbooks

Similar questions

Cyclic voltammetry (CV) is a powerful and popular electrochemical technique commonly employed to investigate the reduction and oxidation processes of molecular species
The mobility of the NH4+ ion is known is 7,623 x 10 ^-8 m2/Vs. Count:a. The molar conductivity of the NH4+ ionb. Ion velocity, when a voltage of 15 V is applied to the cell with separate electrodes 25 cm awayc. The transport number of NH4 + ions in CH3COONH4 solution if the ion is mobility CH3COO is 4.239 x 10-8 m2/Vsd. The amount of current carried by the NH4+ and CH3COO ions when the appliance set is connectedwith a coulometer I2 electrolyzed for 60 minutes as much as 50 mL. 10 mL of This solution was reacted with 20 mL of 0.05 M Na2S2O3 solution according to the following reaction:2S2O32- + I2 → S4O62- + 2I-
Zinc may be directly leached from zinc-lead sulphide concentrates by reaction with sulphuricPbS(s) + H2SO4 + 1 O2(g) → PbSO4(solid) + SÂ° + H2O 21ZnS(s) + H2SO4 + 2 O2(g) → ZnSO4(aq) + SÂ° + H2Oacid and oxygen. In addition, lead sulphide will be oxidized to give insoluble lead sulphate:Assume that a plant is to treat 400 t/day of concentrate containing 20.0 weight % Zn as ZnS and 110.0 weight % Pb and PbS. The concentrate and leach solution enters the leaching vessel at 32.0% solids. During the leach, 85.0% of the zinc is extracted and all the lead sulphide is oxidized. After the leaching step, the slurry passes to a thickener.(a) Calculate the concentration of Zn (in g/L) in the solution passing to metal recovery. Assume a solution density of 1.11 g/mL.(b) Calculate the tonnes per day of elemental sulphur produced.NOTE: â€œ% solidsâ€ is the solids content of a slurry (consisting of particles and solution) and is defined as…
For the reduction 2FeCl3 + SnCl2 =====➔ 2 FeCl2 + SnCl4 in aqueous solution the following data were obtained at 25oC t(min) 1 3 7 11 40 Y 0.01434 0.02664 0.03612 0.04102 0.05058 Where y is the amount of FeCl3 reacted in moles per liter. The initial concentrations of SnCl3 and FeCl3 were respectively, 0.03125, 0.0625 moles/L. a.)Show that the reaction is third order (derive the rate law), and b.) calculate the average specific rate constant.
If the peak potential difference in a single cyclic voltammetry curve is 58 mV, this indicates that The charge transfer reaction is fast. The charge transfer reaction is reversible. The charge transfer reaction uses one electron. The reaction involved is independent of pH.
Two Copper strips were used to determine the effect of electrolysis time and immersed in 3.080g of Cu (NO3)2 dissolved in 25mL of DI water. The weight of one copper strip act as an anode is taken before the reaction and after the reaction to calculate the change in mass. 1.0A of current and 7.50 V is used throughout the experiment Calculate the theoretical mass that should be obtained at each time interval and Compares the theoretical mass (mg) of copper and the actual mass deposited (obtained from the electrolysis, ∆m) by calculating the %error at different times. Briefly discuss the observed results. Is there any trend observed? Positive Anode (Copper strip): Cu(solid) ®Cu2+(aqueous)+2e- Negative Cathode(Copper strip ): Cu2+(aqueous)+2e- ®Cu(solid) Time interval (min) 2.5 5.0 7.5 10 Initial mass of strip (mg) 3432 3390 3297 3141 Final mass of strip (mg) 3390 3297 3141 2939 Mass change Dm (mg) 44 93 156 202 Michael Faraday…
7. Consider a1Msolution ofNa3AsO4. Write the charge and mass balance equations for this system. (please type answer not write by hend)
Initial mass of copper electrode (g) 1.201g Final mass of copper electrode (g) 1.163g Initial mass of key (g) 8.464g Final mass of key (g) 8.525g Average current (A) 0.015 A Time of current application (s) 30 min Use your data from measuring the mass of the electrode and the key to calculate the actual number of moles of copper that plated out.
1. Purification of chromium can be achieved by electrorefining chromium from an impure chromium anode onto a pure chromium cathode in an electrolytic cell. How many hours will it take to plate 15.5 kg15.5 kg of chromium onto the cathode if the current passed through the cell is held constant at 42.0 A42.0 A? Assume the chromium in the electrolytic solution is present as Cr3+Cr3+.
What are the advantages of glass electrode over hydrogen electrode? Please explain briefly.
A sheet of steel with an initial nitrogen concentration of 0.066% is exposed to an atmosphere containing 0.2% nitrogen. After 6 hours, the concentration of nitrogen 5 mm into the surface of the steel sheet is 0.090%. At what temperature is this process taking place? Assume that D0 = 4.7 x 10-7 m2/s, QD = 76.6 kJ/mol. Refer to the erf table.
The mobility of a Li+ ion in an aqueous solution is 4.01×10−8 m2s−1 V−1 at 25°C. The potential difference between two electrodes in the solution placed 1.0 cm apart is 12.0 V. What is the lithium ion current rate? (Use μms-1 for your answer)