Assume that a digital system has eight 8-bit registers RO to R7. Assume that initially the register values are as follows: RO = 6, R1 = 11, R2 = 17, R3 = 23, R4 = 27, R5 = 31, R6 = 37, R7 = 41. Determine the final values of all affected registers after the following sequence of microops are executed. You can show the results in binary, hexadecimal or decimal. RI E -RO R2 + R4 – R3 R5 ER6 + R2 R6 E R1 AR7 R7 E R1 O R2 R3 € sl R7

Assume that a digital system has eight 8-bit registers RO to R7. Assume that initially the register values are as follows: RO = 6, R1 = 11, R2 = 17, R3 = 23, R4 = 27, R5 = 31, R6 = 37, R7 = 41. Determine the final values of all affected registers after the following sequence of microops are executed. You can show the results in binary, hexadecimal or decimal. RI E -RO R2 + R4 – R3 R5 ER6 + R2 R6 E R1 AR7 R7 E R1 O R2 R3 € sl R7

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

A 4-bit universal shifting register QA, QB, QC and QD and a single serial input called SI, has two inputs so that they determine how to operate, as follows: M0M1 = 00 indicates that it should keep the value of the current outputs, M0M1 = 01 indicates that you should shift right, M0M1 = 10 indicates that you should shift left, and M0M1 = 11 indicates that you should parallel load inputs A, B, C, and D. Design a minimum circuit that implement this record and draw the final schematic diagram. Include the entire design procedure
1. Write down 2- differences between Von-Neumann and Harvard architecture. 2. you are executing an instruction, SUB $s0, $s1, $s2 (address 0x20). Draw the datapath of this instruction when $s1=10, $s2=5. When are the stages in this datapath? Mark the components which are active in corresponding stages. 3. How to store(1050000)10 in register $s0? Write down the instructions that stores the data in $s0 register.
. Flag Register is a special purpose. Name two types of registers used in 8086 microprocessor. Consider the given example and explain how over flow, carry, parity and auxiallry flag will work on these instruction. MOV AL, 50 (50 is 01010000 which is positive) MOV BL, 32 (32 is 00110010 which is positive) DD AL, BL (82 is 10000010 which is negative)
Design a micro programmed system that adds two 16-bit numbers stored in the register pair AB and CD (A, B, C & D are 8-bit registers). The sum is to be saved in the register pair AB. Assume that only an 8-bit adder is available.
Start counting using 13-bit counter 1 (internal initialization). When the carry bit is logic 1, store the current count value in the DPTR register. Can you write the answer with assembly code using 8051 - AT89S8253 architecture?
What is the hexadecimal value stored in Register A after the following assembler has executed? LDA #0x71 NOTA NOTA LDR B,#0x71 ADC A,B LDR B,#0xEB ADC A,B NOTA LDR B,#0xD5 ADC A,B LDR B,#0x53 SBC A,B LDR B,#0x19 SBC A,B LDR B,#0x5E SBC A,B
Design a binary multiplier that multiplies two 8-bit binary number by following design rules thatshown in class. The Q and B are the two separate 8-bit binary inputs, C is the 3-bit sequence counterand R is the 16-bit result. (Note: Explain the registers that you will use to establish given process.) The steps are writing algorithm Drawing circuit undetailed (Just use the box, which have only writin under that their functions) Draw logic circuits one by one showing the internal structure of the boxes. Mahe flow chards for registers
Please answer this question in 10 mins i will surely rate your answer. 1. A combinational circuit adds either a 1 or 2 to a 4-bit binary number A. Assume that the inputs bb A3, A2, A1, A0 represent the 4-bit binary number. Another input is a control signal C. The circuit has outputs assumed to be X3, X2, X1 and Xo, which represent the 4-bit number X. When C=0, X=A+1 and when C=1, X=A+2. Assume that the inputs for which X > (1111)2 will never occur. Show the design steps in detail including truth tables, K-Maps, logic equation minimisation. Finally, design this circuit using only NAND gates and inverters .
Please design a 6:1 multiplexer following the below procedures with data inputs of D5, D4, D3,D2, D1, D0 and output of Y.1 How many select signals are needed for this Mux.2) List a truth table for this Mux. Note: for all the unused combinations of select signals, Y=D53) Develop an optimized function for this Mux.4) Sketch the logic diagram of implementing this 6:1 Mux.5) Write a complete VHDL structural model to implement the above 6:1 multiplexer. Assume allthe required sub-component (standard gates) VHDL models are given/known that you can use
1. How many shift pulses are needed to serially shift the contents of a 3 bit register to another 3 bit register?A.3B.12C.6D.22. What will be the state of a MOD64 counter after 90 input pulses if the starting state=000000?A.100100B.011010C.010110D.011100
Write shift routines (LSL, LSR, ASR) that allow you to arithmetically shift 64-bit values that are stored in two registers. The routines should shift an operand left or right by one bit.
Topic is about shift registers in electrical engineering. 1. What is the main functional purpose of a register? We are looking for the specifics of what a register does in isolation, not with respect to applications. 2. In what cases might we use serial and parallel inputs/outputs? 3. Describe the purpose of the debouncer in your own words. 4. Is an SN5474 the same as an SN 7474? If not, how do they differ?