Answered: Which of the following is correct for a…

Which of the following is correct for a open loop system ? O a. No comparison element O b. Automatic Control system O c. Use feedback element O d. Have feedback

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter1: General Principles Of Motor Control

Section: Chapter Questions

Problem 4RQ: Explain the difference between manual control, semiautomatic control, and automatic control.

See similar textbooks

Related questions

Q: Please explain, in our own words, the difference between the "d operator" and the "8 operator."

A: Both operators are used to represent change in some quantity.

Q: (PID solution with the requirements and simple explanation. Thx) INSTRUCTION: Given three bare…

A: Feedback Solution (1): This feedback control starts with a level transmitter that will measure the…

Q: The graph for on-off control mode operation is............

A: The graph for on-off control mode operation is

Q: Integral controller has large overshoot. Select one: O True O False

A: Demerits System gets to be sluggish due to the expansion of fundamentally term. Takes bigger time…

Q: H.W 2:Design 4:16 Decoder from 2: 4 Decoder with truth table ,Boolean Functions and Logic Diagram.

A: A 4x16 decoder has 4 inputs and 16 outputs, with the outputs going high for the corresponding 4-bit…

Q: ») Explain the basic components of closed loop system shown in figure (a) Error Detector Actuating…

A: A closed-loop control system can be defined as, a system that has a feedback loop (or) a control…

Q: Define winkler method

A: Given Data⇒ winkler method Problem statement⇒ Problem says Define winkler method

Q: Identify the input and output for an automatic refrigerator. Cite instances whether it will be…

A: Temperature control systems (home thermostats) and cruise control systems are two examples of…

Q: Assume Shipping cost per unit between nodes 1 and 2 is $10 and between nodes 2 and 3 is S -30 +10…

A: The Total Demand of Model = 30 +10 = 40 The Total Supply of Model = 30

Q: quation for the given data. A four-bar mechanism is to be designed in utomotive industry to perform…

Q: 97) In which operating condition is the PCM most likely using the open loop strategy? O Highway…

Q: Which one is not called as classical controller? O a. Programmable logical controller O b. PID…

A: As, we know the most common classical controller is PID controller.

Q: xplain the role of feed back signal and error signal in a closed-loop control system

A: Role of Feedback system:- Feedback is taken into account to be a significant part of a closed-loop…

Q: is an interconnection of components forming a system configuration that will provide a desired…

Q: cabout 4% defecti nstruct a control cl

Q: One of the disadvantage of negative feedback loop is lag caused because it can only be exerted after…

Q: Which controller takes corrective action against peak overshoot? O a. l-controller O b. P-controller…

A: D-controller is used to sense the rate of change of the error signal and controlled output is…

Q: Discuss the control system (the level controller and the temperature controllers) shown in figure…

A: As in the figure temperature transmitting to the reactor to the temperature control.

Q: Explain Quick Return Mechanism along with commercial application

A: Generally, a rotary machine (motor) is used to create to-fro motion i.e. the rotational motion is…

Q: Identify the system which is unreliable. a.

A: In manufacturing Engineering Machine input and output is controlled by 2 systems by close loop or…

Q: The delay in the response of any feedback system is called as system lag. Select one: O True O False

A: System: It is a collection of the parts which are arranged in a systematic manner to gain a specific…

Q: The system will have a direct connection between the output and input.

A: Out of the two systems (i) Open Loop System and (ii) Closed Loop System, in Open loop system, the…

Q: The symbol used for output device in PLC is a. Ob. C.

Q: Fill in the blanks with the most convenient answer: The main problem with very sensitive to…

A: In mechatronics systems, the input may or may not depend on output. Based on this system can be…

Q: Sketch an automatic control system diagram for: 1. Hydraulic Control System 2. Electric Control…

A: Given Control System To find Diagram for automatic control

Q: (b) Identify the following elements of the given closed loop control system. (1) Process Element…

A: The closed loop system is given by -

Q: What is system?

A: Given Data : System

Q: Which type of control system is used in the given block diagram? Write the definition.

A: The Control system used in this diagram is open-loop control system.

Q: The hammer speed is desired to be at x'= 10 m/s. Draw %3D the free hand flow diagram of the closed…

A: Given : speed - 10 m/s To find Closed loop diagram

Q: controller DC MOTOR temperature VALF sensor hot water Steam Inlet HO outlet heat exchanger cold…

A: Cold water enters the heat exchanger system as seen in the figure, and cold water heats up through…

Q: In serial manipulators, force propagates from joint to joint in the backward direction (end-effector…

A: True

Q: If the load disturbances in flow control systems are rapid and enought to cause the system to…

A: Following is the answer to the above question

Q: Human-aided control system for controlling a fluid level in a tank is shown in Figure Q2a. Here H…

A: Draw a block diagram for human aided control system for controlling the fluid level in the tank.

Q: What is an interrupt? define and explain how Transfer of Control via Interrupts?

Q: For a FANCU Robot What position should the Teach pendant Enable/Disable switch be in for manual…

A: The FANUC automaton i series could be a series of extremely reliable intelligent robots with the…

Q: hat are the differences between the contact mode and the tapping mode (feedback, interaction forces,…

A: The contact mode A cantilever tip is dragged across the surface of the sample in the static contact…

Q: Explain the robot hand grasping force control system in detail with block diagram and justify it as…

A: Robot hand grasping force : So when a robot hand want to grasp an object it requires an certain…

Q: As far as signals & sytems(s&s) is concerned, discuss using s&s concepts in summary, how a feedback…

A: To discuss : About feedback system. Concept used : Feedback system, Input Systems are signal…

Q: (a) What is the function of Digital to Analog Converter (DAC)? Mention its types. DAC. (b) Identify…

A: DACs are commonly utilized in music players to change over computerized information streams into…

Q: The symbol used for output device in PLC is Oa. O b. HE Oc. O d. -O-

A: Option d is correct answer.

Q: Why PID controller response is better than P and PI controller response

A: The basic principle behind a PID controller is to read a sensor, then calculate the required…

Q: FOR A FANUC 6 axis robot What is the purpose of the Deadman’s switch?

A: 1.The FANUC S-6 is a six-axis, standard construction, electrical servo-driven mechanism that has…

Concept explainers

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.

Question

100%

Which of the following is correct for a open
loop system ?
O a. No comparison element
O b. Automatic Control system
O c. Use feedback element
O d. Have feedback

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Hello Sir.Good Evening. I'm currently taking an exam Control System Lesso I have a question related Control System Lesson. The following below is my question.Please advise fast, Thank you so much.
One advantage of a modern control system is A. simplicity. B. faster response. C. ability to modulate. D. that they are less expensive.
Explain the difference between manual control, semiautomatic control, and automatic control.
Name three types of automatic controls.
2) Explain the in detail control system for steam supply to the engine of centrifugal Watts’Governor with block diagram and justify it as closed loop system.
There is a CNC system with one sensor and one actuator. Draw a block diagram f. CNC system with a master PC and a PC based controller. Explain the tasks of components
Block diagram and explanation of the applications of open loop system: Automatic washing machine, Automatic toaster system, Traffic light controller and Furnace without thermostatic control but with timing device
What is an interrupt? define and explain how Transfer of Control via Interrupts?
The graph for on-off control mode operation is............
A major disadvantage of on/off control is that it cannot work for applications requiring very small changes from the set point (sp) a. true b. false
Pneumatics problem 1. What is an automatic controller? 2. What is the difference between a close loop and open-loop system?
For a FANCU Robot What position should the Teach pendant Enable/Disable switch be in for manual operation?