Identify the working substance, specify the kind of system and sketch the system boundary Example: Nitrogen, at a pressure of 200 kPa and a temperature of 25C, flows at a velocity of 20 m/s through a pipe with a diameter of 35-mm. Working Substance: Nitrogen System: Open Nitrogen 1. Oxygen is compressed in a piston-cylinder arrangement Working Substance: System: Drawing: 2. An adiabatic condenser receives 100 kg/s of steam at 92% quality and 60 kPa. The steam leaves at 60 kPa and 600C. The cooling water enters at atmospheric pressure and 400C and discharges at 600C. Working Substance: System: Drawing 3. Two streams of air are mixed in a steady-flow mixing chamber that has two inlets and a single exit Working Substance: System: Drawing

Identify the working substance, specify the kind of system and sketch the system boundary Example: Nitrogen, at a pressure of 200 kPa and a temperature of 25C, flows at a velocity of 20 m/s through a pipe with a diameter of 35-mm. Working Substance: Nitrogen System: Open Nitrogen 1. Oxygen is compressed in a piston-cylinder arrangement Working Substance: System: Drawing: 2. An adiabatic condenser receives 100 kg/s of steam at 92% quality and 60 kPa. The steam leaves at 60 kPa and 600C. The cooling water enters at atmospheric pressure and 400C and discharges at 600C. Working Substance: System: Drawing 3. Two streams of air are mixed in a steady-flow mixing chamber that has two inlets and a single exit Working Substance: System: Drawing

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Refrigerant -134 a enters the evaporator of a refrigerator as saturated vapor at −20∘ C and leaves at −10∘ C and 100 kPa. The volumetric flow rate at the inlet is 0.25 m 3/s Calculate the mass flow rate.
A boiler takes in feed water at 70 °C and generates steam at a pressure of 10 bar and drynessfraction 0.92. The wet steam enters a superheater and emerges with the same pressure at atemperature of 400 °C. If the steam flow rate is 5 tonnes per hour, determine (i) the rate atwhich heat transfer takes place in the boiler and (ii) the rate at which heat transfer takes placein the superheater. State any assumptions you have made in relation to the steady flowequation for the process.
Atmospheric air at 40°C dbt and 55% RH is passed over a cooling coll at the rate of 600 m/mint. At exit from coil the air is saturated and its temperature is 8°C. The condensate also leaves at 8°C. Determine the amount of condensate leaving coll per minute and refrigeration in kW. The specific heat of superheated steam may be assumed to be 1.88 kJ/kg-K. Solve the problem without psychromatic chart.
A single effect evaporator was used to concentrate 10000 kg / hr of tomato juice from 5% total solids to 30% total solids. The juice enters the evaporator at 25 ° C. The evaporator is operated on Steam (85% quality) at 143.27 kPa. The vacuum in the evaporator allows the juice to boil at 75 ° C. The specific heat of the dilute material is 4.1 kJ / (kg ° C) and the concentrate product is 3.1 kJ / (kg ° C). a. Steam demand rate = kg / hour. b. Steam economy when condensate temperature is released at 75 ° C. = (kg of water evaporated / kg of steam)
Steam is delivered to turbine at 5.4 MPa and 600 degree C. Before condensation at 31 degree C, steam is extracted for feed water heating at 0.6 MPa. The turbine exhaust is 60 degree C. the required values of some state point properties are tabulated below. 7. Determine the quality of steam at the condenser inlet.
The refrigerant in an evaporator goes through phase change at a constant temperatureof −30◦C. The rate of vaporization of the refrigerant is 0.15 kg/s. The latent heat of vaporization ofthe refrigerant is 412.1 kJ/kg. Air enters the evaporator at mass flow rate 1.1 kg/s with a temperatureof 45◦C. Assume air has a constant specific heat of 1007 J/kg·K. What is the effectiveness of this heatexchanger?
Saturated water vapor at 40°C is to be condensed as it flows through a tube at a rate of 0.20 kg/s. The condensate leaves the tube as a saturated liquid at 40°C. The rate of heat transfer from the tube is (a) 34 kJ/s (b) 481 kJ/s (c) 2406 kJ/s (d) 514 kJ/s (e) 548 kJ/s
a power plant steam, steam is continuously extractedfromthe turbine and in a heat exchanger there is a condensation of the extracted steam. The energy released during condensation of steam is used to operate a heat engine. A heat engine receives thermal energy at a rate of 1200 kJ/hr from condensing steam and rejects waste heat to a lake at 20°C at a rate of 800 kJ/hr. Determine the lowest possible condensing steam temperature.
a forward feed triple effect evaporator is used to fed 13608 kg/hr of NaOH solution containing 10 wt% solute. the entering feed temperature is 37.8°c. it is to be concentrated to a 50% NaOH solution. the steam used to enter at 58.6 kpa gage. the absolute pressure in the vapor space of the third effect is 6.76 kpa. the heat transfer coefficient are u1=6246, u2=3407, and u3=2271 w/m²k. all effects must have the same area. calculate the surface area and steam consumption Show steps and solutions .
he refrigerant R-134a enters the compressor of a refrigeration machine at a pressure of 140kPa and a temperature of -10°C, and exits at a pressure of 1MPa. The volumetric flow of the refrigerant entering the compressor is 0.23m3/minute. The refrigerant enters the throttling valve at a pressure of 0.95MP and at 30 °C, and exits the evaporator as saturated steam at -18 °C. The adiabatic efficiency of the compressor is 78%. Show the cycle in the T-s diagram. a) Power required to start the compressor b) Calculate the heat withdrawn from the cooled environment in unit time, COPSM=? c) Calculate how much the pressure of the refrigerant drops between the evaporator and the compressor and how much the heat gain is.
Air is compressed in a compressor through the purely polytropic, purely isothermal, and intercooling as shown in the diagram between the same pressure limits. Select the area that indicates the work saved for the intercooling process comparing to the purely polytropic one _____________ A. 1-X'-2'-P2-P1-1 B. X-X'-2-2"-X C. 1-X-X'-2-P2-P1-1 D. 1-X'-2"-P2-P1-1
Refrigerant-12 enters the throttling valve of a heat pump system at 200 psia as a saturated liquid and leaves at 20 psia. Determine (a) the temperature drop across the throttling valve. (b) what is the expected rating of the valve in terms of its pressure drop?