If a batch o be tested for the average weight of its tablets as H0: u = 200. The standard deviation of tablet weight of the batch is 15 and the samples to be taken are of size 9. If the null hypothesis is true at sig. level of 0.05, which of the following sample means would have a confidence interval with an upper limit that is equal to the hypothesized mean and in this case the null hypothesis is calculation) (round up the reliability coefficient in your

If a batch o be tested for the average weight of its tablets as H0: u = 200. The standard deviation of tablet weight of the batch is 15 and the samples to be taken are of size 9. If the null hypothesis is true at sig. level of 0.05, which of the following sample means would have a confidence interval with an upper limit that is equal to the hypothesized mean and in this case the null hypothesis is calculation) (round up the reliability coefficient in your

MATLAB: An Introduction with Applications

6th Edition

ISBN:9781119256830

Author:Amos Gilat

Publisher:Amos Gilat

Chapter1: Starting With Matlab

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A sample of 12 radon detectors of a certain type was selected, and each was exposed to 100 pCi/L of radon. The resulting readings were as follows: 105.6 90.9 91.2 96.9 96.5 91.3 100.1 105.5 99.6 107.7 103.3 92.4 Does this data suggest that the population mean reading under these conditions differ from 100? (a) State the null and alternative hypotheses. (b) Calculate, correct to 2 decimal places, (i) the sample mean, x ; and (ii) the sample standard deviation, s. (c) Evaluate the appropriate test statistic. (d) Test these hypotheses at   0.05 level of significance.
The desired percentage of SiO2 in a certain type of aluminous cement is 5.5. To test whether the true average percentage is 5.5 for a particular production facility, 16 independently obtained samples are analyzed. Suppose that the percentage of SiO2 in a sample is normally distributed with ? = 0.32 and that x = 5.21. (Use ? = 0.05.) (a) Does this indicate conclusively that the true average percentage differs from 5.5?State the appropriate null and alternative hypotheses. H0: ? = 5.5Ha: ? ≠ 5.5H0: ? = 5.5Ha: ? ≥ 5.5 H0: ? = 5.5Ha: ? < 5.5H0: ? = 5.5Ha: ? > 5.5 Calculate the test statistic and determine the P-value. (Round your test statistic to two decimal places and your P-value to four decimal places.) z = P-value = State the conclusion in the problem context. Do not reject the null hypothesis. There is sufficient evidence to conclude that the true average percentage differs from the desired percentage.Reject the null hypothesis. There is sufficient evidence…
With reference to the uniform population of Exam-ple 4, use the definition of consistency to show that Yn, the nth order statistic, is a consistent estimator of theparameter β.
How large a sample would have to be drawn to make these limits differ by only 0·1 gm, assuming that the standard deviation of the whole distribution is 1·25 gm at 5% L.O.S.?
Suppose a certain species of fawns between 1 and 5 months old have a bodyweight that isapproximately normally distributed with mean μ = 30 kilograms and standard deviation σ = 4kilograms. Let x be the weight of a fawn in kilograms. Convert the following x interval to a zinterval. Round to the nearest hundredth. .x < 44.0 Group of answer choices z < –18.50 z < 3.50 z > –18.50 z < 18.50 z > 3.50
Suppose that on a certain of SRP with a posted speed limit of 65kph, the speed of all vehicles have a bell-shaped distribtution with a mean of 72kph and a standard deviation of 3kph. A.Using the empirical rule, find the percentage of vehicles with the following speeds on this section of SRP a.)63 to 81 kph b.)69 to 75 kph B.Using the empirical rule, find the interval that contains the speed of 95% of vehicles travelling on this section of SRP pls help me
An industrial sewing machine uses ball bearings that are targeted to have a diameter of 0.75 inch. The lower and upper specification limits under which the ball bearings can operate are 0.73 inch and 0.77 inch, respectively. Past experience has indicated that the actual diameter of the ball bearings is approximately normally distributed, with a mean of 0.754 inch and a standard deviation of 0.005 inch. Type calculations and/or use Excel functions, including the explicit arguments for each function, in answering these questions. a) What proportion of the ball bearings produced meet the design requirements? b) Of 1000 bearings , how many are expected to be too large to function in the sewing machine? c) What diameter represents the 80th percentile of the bearings produced by this machine?
In a test of HO; u = 80 against HA,: u z 80, a sample of observations had a mean X = 78 and standard deviation s = 4.1. Find the p-value for the test. Compute it manually, not excel.
Assume X_1, X_2, .....X_n are random samples from X~Exponential(θ).1) Find the MLE estimator of θ .
The Toylot company makes an electric train with a motor that it claims will draw an average of only 0.8 ampere (A) under a normal load. A sample of nine motors was tested, and it was found that the mean current was x = 1.34 A, with a sample standard deviation of s = 0.41 A. Do the data indicate that the Toylot claim of 0.8 A is too low? (Use a 1% level of significance.) State the null and alternate hypotheses. H0: μ ≠ 0.8; H1: μ = 0.8H0: μ = 0.8; H1: μ ≠ 0.8 H0: p = 0.8; H1: p ≠ 0.8H0: p ≠ 0.8; H1: p = 0.8H0: p = 0.8; H1: p > 0.8H0: μ = 0.8; H1: μ > 0.8 What sampling distribution will you use? What assumptions are you making? The Student's t, since we assume that x has a normal distribution with known σ.The standard normal, since we assume that x has a normal distribution with unknown σ. The standard normal, since we assume that x has a normal distribution with known σ.The Student's t, since we assume that x has a normal distribution with unknown σ. What is the value of the…