If a grounding electrode conductor is connected at the first system disconnecting means or overcurrent device, the bonding jumper is sized the same as the ____. Select one: A. EQUIPMENT BONDING JUMPER B. POSITIVE CONDUCTOR C. SUPPLY-SIDE BONDING JUMPER D. NEUTRAL CONDUCTOR

If a grounding electrode conductor is connected at the first system disconnecting means or overcurrent device, the bonding jumper is sized the same as the ____. Select one: A. EQUIPMENT BONDING JUMPER B. POSITIVE CONDUCTOR C. SUPPLY-SIDE BONDING JUMPER D. NEUTRAL CONDUCTOR

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter31: Wiring For The Future: Home Automation Systems

Section: Chapter Questions

Problem 7R: When selecting cables for a structured wiring system or computer hookups, the best choice is to...

See similar textbooks

Related questions

Q: What is the minimum-size supply-side bonding jumper required if installed on the line side of a…

A: The supply-side bonding jumper is installed on the line side of a 300-ampere service disconnecting…

Q: 5. What is the minimum depth that a USEB90 cable, used as a service conductor, can be buried…

A: USEB 90 cable is used as underground cable to transfer electrical power in houses. These types of…

Q: The insulation rating of class 3, PLTC, FPL, CM cables rated at ____ volts.

A: Ans. 300 volts

Q: In the conduit layout shown in picture attached, determine how many wires are contained in each…

A: The circuit is shown below: Between the three-phase line and the disconnect switch. The switch is…

Q: Identify the minimum distance requirements between network cables and power sources and identify…

A: Cable is the medium in a network through which information moves from one network device to another.…

Q: The grounded circuit (system) conductor is generally not permitted to be used to ground equipment on…

A: Given, The grounded circuit (system) conductor is generally not permitted to be used to ground…

Q: The NEC requires the grounded conductors to be routed to the service disconnecting means enclosure…

A: According to the NEC article code 250.186 (B), "System with a grounded conductor at the service…

Q: 4.a. The installation of motor controllers and combination load equipment is not permitted if the…

A: A motor controller is a device or combination of devices, that can control how an electric motor…

Q: If a 1 1/4-in. EMT raceway containing three conductors is already filled to 20%, what is the…

A: Need to find cross sectional area of raceaway

Q: Q.4. Mention the specifications of EIA/TIA recognized cables and its standard number for each type…

A: With industry input, the TIA/EIA cable standards have been developed by the Telecommunications…

Q: 9. How is equipment containing ungrounded electrical systems required to be marked? A. With green…

A: An ungrounded system is a system that is not grounded intentionally. The neutral wire of an…

Q: Define cable rating in a built environment

A: Cable selection and application : It is essential to know cable construction, characteristics,…

Q: 11. What are at least two instances where a splice is allowed to be made in underground consumer's…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: Identify and explain the safety procedures and precautions when working with tools and equipment's…

A: Electrical cables are used for transferring the signals and are also used for long distance…

Q: 8- Generally as of the operating voltage which of the following options are the correct words that…

Q: Which of the following statements about equipment grounding conductors (EGCs) is true? A. The…

A: Statement about the equipment grounding conductors (EGCs)

Q: The equipment grounding conductor of a grounding-type receptacle or a branch-circuit extension is…

A: True, The equipment grounding conductor of a grounding-type receptacle or a branch-circuit extension…

Q: 12. What is the conduit and wire equivalent to a 400A bus duct with both copper and aluminum?…

A: The National Electrical Code (NEC) is a collection of rules for the secure electrical wiring wiring…

Q: List the methods by which an equipment grounding conductor is connected to a device box

Q: what is grading of cables, explain proper in details with block diagram

A: In a single-core cable, the conductor is surrounded by the dielectric material with an outer…

Q: b) Differentiate between Insulated-Neutral and Earthed-Neutral systems as applied to electrical…

A: Question. b) Differentiate between Insulated-Neutral and Earthed-Neutral systems as applied to…

Q: A conductor with continuous white or gray covering shall be used only for the grounded circuit…

A: According to article NEC 200.6, the facts about the identification of the Grounded conductors are…

Q: How far can a 230V, 50A, three-phase load be located from a panelboard if it's fed with 3 AWG…

A: The Length of the load from the panel board is calculated as shown below

Q: Basically, ______receptacles are required to be installed if an equipment grounding conductor is…

A: Article 406 of NEC covers the installation of receptacles of both grounded type and non-grounded…

Q: The Voltage Regulation of a Transmission Line should be _____? A. very high percentage. B. more than…

A: C. Zero or nil Option C is correct.

Q: How many conductor volume allowances should be applied for the equipment grounding conductors in the…

A: We need to answer how many conductor volume allowances should be applied for the equipment grounding…

Q: 6. Which of the following is a condition that a liquidtight flexible metal conduit must meet in…

A: Given :few mcqs on flexible metal conduit

Q: Determine the Primary Conductor Size (include the AWG size number), Secondary Conductor Size…

A: P= 90 KVA Three phase transformer 400/230 V

Q: Four No. 12 and four No. 10 conductors are to be installed in a EMT conduit. What size EMT conduit…

A: Conductors size is selected on the basis of assigned numbers. As the assigned number increases then…

Q: Which of the following is a term missing from the National Electrical Code but used by manufacturers…

A: ANSWER (1) Grounding Triad is the term which is missing in NATIONAL…

Q: Which of the following is an installation requirement for the grounding electrode conductor in a…

A: ANSWER - (A,C,D) is correct EXPLANATION- Option (A)- Grounding…

Q: procedures

A: Explanation: The safety procedures and precautions to be taken when working with tools and…

Q: In an ungrounded electrical systems with conductors installed in grounded metal raceways and…

A: In an ungrounded system, the system has no direct connection with the grounding electrode. When the…

Q: Determine the minimum number of cubic inches required for two 10 AWG conductors passing through a…

A: AWG or American Wire Gauge is the US standard measure for the diameter of electrical conductors. The…

Q: Briefly discuss the loaded and non-loaded telephone cables

A: Loading is the process to increase inductance of line by adding lumped inductors atpredefined…

Q: of p o How many conductors enter the ceiling fan/light wall box? Switch ond out let boxes s tirst…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: 14. If the total circular mil area of the largest ungrounded service-entrance conductor for a…

A: Explanation: The equivalent area of four ungrounded paralleled 500 kcmil conductors is 2000 kcmil.…

Q: When installing a surge arrester at the service of less than 1000 volts, the grounding conductor…

A: Equipment Grounding Conductor (EGC) – A conductive path that 's a component of a decent ground-fault…

Q: It is not uncommon for electrical designers to require an equipment grounding conductor to be…

A: True, Because for each and every equipment there is different grounding required according to the…

Q: Twenty-two 14 AWG copper conductors are run in conduit. Each conductor has type THHN insulation. the…

A: The given information is:

Q: 13. If the largest ungrounded service-entrance conductor for a service is 750-kcmil copper, what is…

A: Choose the correct option, If the largest ungrounded service-entrance conductor for a service is…

Q: Identify and describe the step-by-step process used to install cable in the NCT Colledge buildings

A: according to question, Identify and describe the step-by-step process used to install cable in the…

Q: A? Conductor is defined in NEC 240.2 as a conductor, other than a service conductor, having…

A: The article 240.2 determine the current limiting of the over current protective device is used to…

Q: How many 14 AWG THHN conductors, including an equipment grounding conductor, can be installed in a…

A: Here we have to refer standard tables, When determining the maximum number of conductors permitted…

Q: The voltage drop percentage for a panel feeder with a no continuous load of 180A, using 3/0 THWN…

A: Given data, A 3/0 THWN copper conductors at 480 V Length, L=248' Load current, I=180 A

Q: What size equipment grounding conductor is used with # 8 AWG nonmetallic-sheathed cable

A: The minimum size equipment grounding conductor is selected on the basis of the current rating…

Concept explainers

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.

Question

If a grounding electrode conductor is connected at the first system disconnecting means or overcurrent device, the bonding jumper is sized the same as the ____.

Select one:

A. EQUIPMENT BONDING JUMPER

B. POSITIVE CONDUCTOR

C. SUPPLY-SIDE BONDING JUMPER

D. NEUTRAL CONDUCTOR

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Compensation Techniques in Transmission Line

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

When selecting cables for a structured wiring system or computer hookups, the best choice is to select a cable that has a. untwisted pairs of conductors. b. twisted pairs of conductors.
2.a. What's defined as an assembly consisting of a service raceway, guy wires or braces, service head, andany fittings necessary for the termination and support of overhead service conductors?A. Drip loopB. Service lateralC. Service dropD. Service mast 2.b. What's likely to happen when connected parallel conductors are different lengths?A. An NEC violationB. Misidentification of conductor cablesC. An uneven distribution of currentD. Conductor termination
In the conduit diagram shown in attached picture, determine how many wires are in each conduit between each piece of equipment. Identify each wire terminal connection and the quantity of wires, as shown in the example, above the disconnect
In the conduit layout shown in picture attached, determine how many wires are contained in each conduit between each piece of equipment. Identify each wire with a proper terminal marking, as shown in the example, above the disconnect switch.
D.1-. Which of the following names is commonly used for armored cable on commercial and industrial jobsites?A. RomexB. BXC. ECGD. MCD.2. Which of the following is the most common type of conductor termination used in commercial andindustrial wiring applications?A. A pressure connectionB. A wire nutC. A wire spliceD. A crimped connection D.3. Which of the following terms correctly describes a ventilated metal enclosure that supports powerdistribution conductors of up to 8000 A and 69 kV, and that allows for proper phase arrangement of theconductors?A. A trolley busB. A channel racewayC. A cablebusD. A feeder bus
List the methods by which an equipment grounding conductor is connected to a device box.
a. How many feet of 2-conductor bell wire cable are required? ______ b. How many feet of 3-conductor bell wire cable are required? ______
A Type NM cable carries a branch circuit to the outside of a building, where it terminates in a metal weatherproof junction box. From this box, a short length of EMT is installed upward to another metal weatherproof junction box on which is attached a cluster of outdoor floodlights. The first box is located approximately 24 in. (600 mm) above the ground. To Meet Code, do the metal boxes and metal raceway have to be grounded? Yes _______________ No _______________ NEC _______________.
Determine the minimum number of cubic inches required for two 10 AWG conductors passing through a box, four 14 AWG conductors spliced in the box, two 12 AWG conductors terminating to a receptacle, and one 12 AWG equipment bonding jumper from the receptacle to the box.
4. What can installation records be used to determine while servicing equipment?A. Broken connectors in a cable linkB. Problems due to aging during operationC. Broken fiberD. Decreased bending radius during operation
14. If the total circular mil area of the largest ungrounded service-entrance conductor for a service is 2000-kcmil copper, what is the minimum size required for a wire-type main bonding jumper for the service? a) 4/0 AWG copper b) 250-kcmil copper c) 350-kcmil copper d) 500-kcmil copper 15. The minimum-size grounded conductor for a service supplied by a grounded system shall not be smaller than the minimum size required for a(n)______. a) Equipment grounding conductor b) System bonding jumper c) Ungrounded conductor d) Grounding-electrode conductor Note: answer both the questions with proper explanation. As per bartleby honor code I can submit 3 questions. So please answer both
6. Which type of cable would you use to connect two buildings in an office installation?A. Buried loose-tube cableB. Aerial armored cableC. OFNP cableD. Tight-buffered cable