If control requirements are very complex or extensive, a? Can be installed. A. Master sequencer B. Transistor c. Conventional switch d. Double relay

Q: 41 4) obtain the analysis of the synchronous sequential circuit (State table and state diagram) in…

A: Output depends upon present input and present state hence it is mealy machine.

Q: Answer one of the following A. What are the basic types of timers in PLC? B. What are the types of…

A:

Q: Differences between zero current switching (ZCS) and zero voltage switching (ZVS)?

A:

Q: Explanation about magnetic tape recorders?

A: Magnetic tape is a magnetic storage medium that consists of a thin, magnetizable coating on a long,…

Q: A time-proportioning controller with a DC output voltage of 25 volts will produce an average voltage…

A:

Q: Draw the Direct Digital Control block diagram and show the Implementation of the Problem using a…

A: The block diagram of the direct digital control is shown below,

Q: Explain what timer count means?

A: 8254 is a timer/counter device used to solve used to solve timing control problems in a…

Q: What are the advantages of using a PLC-based system over a relay-based system? O There are no real…

A:

Q: the

A: Let us assume initially A, B & C are zero.

Q: Conventional current flows into the output terminal of a solid-state PLC ___________ output module…

A: Conventional current flows into the output terminal of a solid-state PLC sinking input field device.…

Q: Describe DCS and PLC control systems.

A: This question is from control system.

Q: What is the scope and limitation of the automatic fence light controller?

A: Scope of the automatic fence light controller: The automatic fence light controller is very…

Q: 1- Which type of instruction dose INTO normally follow? Which flag does is test?

A: The signals that are directly available from the devices are analog. Hence a conversion is required…

Q: How many different ways can interrupt triggering be done? What are these?

A: Interrupt - Basically interrupt is a block of an instructions which is associated with a specific…

Q: Common selector switches are?

A: => Common selector switches, controls on and off of different current circuit by rotating the…

Q: What is synchronization in digital control systems and mention some methods used to achieve it?

A:

Q: What was the first electrical digital computer comprised of?

A: All latest  computers today are digital computers. An electronic digital computer uses electricity…

Q: eedback and control system Explain how a closed-loop automatic transfer switch (ATS) operates, and…

A: An automatic transmission switch (ATS) is a device that automatically transmits power supply from…

Q: what are the major components of an electronic control system

A: In this case, the major components of an electronic control system needs to be identified.

Q: 3. Design the circuit of Dark activated switch using LDR driven the Solid State Relay?

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: 5. Describe two advantages of a PLC based system over a purely relay based one.

A: To describe the advantages of a PLC based system over a relay based

Q: Industrial Motor Controls, 1.a. Where should the shield for the wire between the D/A module and…

A: Answer 1(a): Between the D/A module and the motor speed controller The shield for the wire should be…

Q: From what location are the first computer instruction ?available on boot up

A: using the bootup process one can make it ready to use by putting in the instructions which it needs…

Q: - Industrial Motor Controls 6.a. Where would be the first place to check if a PLC-controlled motor…

A: A Programmable Logic Controller is abbreviated as PLC. These are used for a programmable variety of…

Q: Draw a plc ladder diagram for blinking lights with timer (1 second interval), start and stop button

A: To draw plc ladder diagram

Q: What is the advantage Synchronizing Lamp compared to Synchrosope?

A: The brief working and advantages are as follows.

Q: Determine the input and output connections for an oven with automatic temperature regulation. Cite…

A: According to the question, we need to determine the input and output connections for an oven with…

Q: 1) What is a PLC? In what position is it used in the SCADA system?

A: PLC stands for Programmable Logic Controller. It is a ruggedized computer used for industrial…

Q: 1. How will you check? And what instrument will you use to determine whether the power supply is…

A: According to our policy we can provide solution. For other solutions repost the questions with…

Q: 15. Upon exiting Reset, which instruction is first executed?

A: Explanation: After the hardware reset, the CPU will start execution at the physical address 0xFFFF0.…

Q: Write information about timer (IC NE555). Note: Please do not handwritten.

A: The following is the answer for the question

Q: The symbol used for normally close contacts in PLC is а. O b. HE с. d.

A: Simple problem on electronics . Look below for explanation.

Q: The symbol used for normally close contacts in PLC is

A: The explanation is as follows.

Q: Which of the following in a control system actuates the powering device? Error Signal Feedback…

A: option B is correct

Q: Why can a 555 timer IC be said to be in monostable mode?

A: The 555 timer IC is an 8-pin robust electronic device. It can be operated as Astable Multivibrator,…

Q: List four of the Advantages /Disadvantages of Relay Control versus PLC Control ?? (Put the letter…

A: The explanation is as follows.

Q: What the disadvantage of remote control??

A: Disadvantages of remote control- When objects block the infrared light it causes difficulties. Need…

Q: 3. Describe working of different proximity sensors used in a PLC.

A: The sensor that is used to determine the object in a specific range is known as the proximity…

Q: Could you perhaps clarify what a programmable interval timer/counter

A: In this question we will write about programmable interval timer ....

Q: What is the function of the assembly program?

A:

Q: In how many different ways can interrupt triggering be performed? What are they?

A: There are different-different ways of interrupt triggering and they are as following, 1. Hardware…

Q: What will happen to the system if the power amplifier is not used in the Infrared Remote controller…

A: The infrared remote control systems have a infrared controlled switch which can be used in number of…

Q: Design a PLC program and prepare a typical I/O connection diagram and ladder logic program for the…

A: In the question, the following data is given. A motor named M and three controlling START/STOP…

Q: Explain the THREE (3) main advantages of Digital Control System.

A: Control system- A control system manages, commands, directs, or regulates the behavior of other…

Q: Design the hardwired control unit using sequence counter method for 8 instructions. Consider 2…

A: We need to design the hardwired control unit using sequence counter method for 8 instructions.…

Q: 1) The Execute Unit (EU) functions? 2) Compare between status & control flags?

A: In this question , we will write about execute unit, status flag and control flag..

Q: . What are the overall functions of a Supervisory Control and Data Acquisition SCADA) system used in…

A: SCADA and PLC are two basic elements of an automation system. They are a backbone of an automated…

Q: What is the difference between a one function and a multifunction electronic control device

A: A one function electronic control device operate only one function, Those equipment which uses…

Q: What function does this implement? Draw the timing diagram

A: