Answered: If design bond stress = 1.5 N/mm² is…

If design bond stress = 1.5 N/mm² is assumed, then the development length of an Fe 500 HYSD bar of nominal diameter 12 mm - which is fully stressed in tension - will be:

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 5CQ

See similar textbooks

Related questions

Q: Situation 2: A steel rod having a length of 50 m is suspended vertically from one end. It supports a…

Q: 2)A of elastic material under plane stress a, b and c with the help of the rosette in the shape…

A: Above given data we have to find stresses

Q: An acetal polymer block is fixed to the rigid plates at its top and bottom surfaces. If the top…

Q: Consider a cylindrical nickel wire 2.0 mm in diameter and 3.2 × 104 mm long. Calculate its…

Q: A solid 45 mm diameter beryllium copper (E = 131 GPa; α = 17.0 × 10−6 /°C) rod is stress free when…

Q: The specimen shown is made from a 25 mm diameter cylindrical steel rod with two 38 mm outer-diameter…

Q: A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress…

A: This question is related to the Strength of material. In this question we calculate axial stress and…

Q: An assembly of a material consists of a brass shell fully bonded to a ceramic core. The brass shell…

Q: A cylindrical specimen of a hypothetical metal alloy is stressed in compression. If its original…

A: nE=2G1+μ105239.7=1+μμ=0.322εd=δdd=0.026220εd=1.31×10-3εh=δhh=h-74.96h

Q: A tensile stress is applied along the long axis of a cylindrical aluminum rod with a diameter of 10…

A: It is required to calculate the strain in the x-direction. Here, is the change in diameter, and d0…

Q: A bar made from aluminum (E = 72 GPa) has a diameter of 12 mm. When the bar is subjected to a…

Q: A rigid horizontal bar (Weight = 20 kips) is supported by two (2) square aluminum columns as shown.…

Q: A metal bar do in diameter and l, gage length failed under an axial tensile load of F. The final…

A: Engineering stress is the ratio of force applied and the initial cross-sectional area of the bar.…

Q: An acetal polymer block is fixed to the rigid plates at its top and bottom surfaces. If the top…

A: We have to determine the value of shear modulus of the polymer as per the given data in the…

Q: In the figure shown below, determine: 1) The final temperature if the normal stress at aluminium is…

Q: A typlcal aluminum-alloy scuba diving tank Is shown. The outside diameter of the tank is 200 mm and…

A: Maximum shear stress in plane = pd/8t Where, d = inner diameter d = 200-2*12 = 176mm

Q: A solid 45 mm diameter beryllium copper (E = 131 GPa; α = 17.0 × 10−6 /°C) rod is stress free when…

A: Find maximum temperature increase?

Q: STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal…

Q: 2.50 Before the 400-kN load is applied, the rigid platform rests on two steel bars, each of…

A: The cross-sectional area of the steel bar is As=1400 mm2. The cross-sectional area of the aluminum…

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure P-108.…

A: Given data in question Area Stresses Loads To find out Maximum value of P so that stresses should…

Q: A leaf spring is made of plates 50 mm wide and 8 mm thíck. The spring has a span of 700 mm.…

A: We have formulaσmax=32(WLnbl2)δmax=38(WL3nbl3E)

Q: a) Which temperature increase AT is required to just close the spacing at the middle? (Note that the…

A: solutionGiven gap ∆=0.26mm aTo close the spcing the deformation in steel rods should be 0.26mmE for…

Q: Compute the value of EIy at midspan for the beam loaded as shown.

Q: A typical aluminum-alloy scuba diving tank is shown. The outside diameter of the tank is 200 mm and…

Q: 1. A homogeneous conical frustum with length, L, of 3m is subjected to an axial tensile load, P, of…

Q: Solve for Vmax and Mmax.

A: The maximum shear force occurs when the larger load is directly on the support. Using equilibrium…

Q: An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a…

Q: An aluminum alloy rod has a circular cross section with a diameter of 7mm. The rod s subjected to a…

Q: For the simple truss shown in the picture the students are required to determine a combination of…

Q: 2.50 Before the 400-kN load is applied, the rigid platform rests on two steel bars, each of…

A: Given:- Before the 400-kN load is applied, the rigid platform rests on two steel bars, each of…

Q: ection of a column consisting of twO ste strips, each of thickness tand width b is shown in the…

Q: A steel beam is simply supported at both end is laterally loaded as in Figure Q3a(i) to bend it…

Q: A cylindrical shell of 500 mm diameter is required to withstand an internal fluid pressure of 5…

Q: If design bond stress 1.5 N/mm2 is assumed, then the development length of an Fe 500 HYSD bar of…

Q: A cylinder of iron, length of 290mm and diameter of 18mm, under the influence of a tensile for of…

A: Given length = 290mm diameter = 18mm tensile force = 60kN

Q: The composite bar of neglible mass is connected to two rods as shown in the figure. If the system is…

A: In this question, as the temperature changes, the steel rod will have some strain and thermal…

Q: In the figure shown below, determine: 1) The final temperature if the normal stress at aluminium is…

Q: A steel rod having a length of 50m is suspended vertically from one end. It supports a tensile load…

A: L = 50m P = 250KN E = 200 GPa = 200 x 109 Pa

Q: Solve for the design strength. Is it stable or not?

Q: In the cage system in Figure 3, circular section steel bars will be used. Calculate the minimum…

Q: Maximum allowable stress for steel = 140 MPa Maximum allowable stress for aluminum = 90 MPa Maximum…

A: Given data in question 3 different materials Length Area Loads Maximum permissible stresses in each…

Q: 2. A steel bar of 750 mm2 cross-sectional area is placed between two aluminum bars, each of 500 mm2…

A: Area of steel = 750mm2 Area of aluminum = 500mm2 Es = 210GPa Eal = 70GPa (σy)s = 240MPa…

Q: Hardness 6.54 (a) A 10-mm-diameter Brinell hardness indenter O produced an indentation 2.50 mm in…

Q: The ratio of the stress at failure to the allowable stress for design is а. Factor of safety b.…

A: Tensile strength:- It is known as "the maximum load in weight for each unit surface area attempting…

Q: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which…

A: find the maximum weight of the beam that the system can support (in KN).

Q: Q3/ compare shape factor (, for stiffness-limited design in bending of a square box section of outer…

A: Shape factor- it is the ratio of Plastic moment to the yield moment of the section. It shows the…

Q: A small element is under loading where o, =-22 MPa, o, =22 MPa and ty =14 MPa. Taking the yield…

Q: You are designing a suspension linkage rod for a new sports car. It will be 12 inches long and…

A: Given:- L=12 inP=10kips(Compression)d = 0.1 inchFOS = 3E=10000ksiσy=40ksiTo find:-d

Q: The brass shell (αb511.6 3 10–6/°F) is fully bonded to the steel core (αs56.5 3 10–6/°F). Determine…

A: The given data is as follows: αb=11.6×10-6/∘Fαs=6.5×10-6/∘FMaximum allowable stress in steel core=8…

Q: AN ALUMINUM TUBE IS FASTENED BETWEEN A STEEL ROD AND BRONZE ROD AS SHOWN IN THE FIGURE. AXIAL LOADS…

A: Total deformation (∆L ) = 5 mm Steel details Es = 210GPa = 2.1 × 105 N/mm2 Permissible stress in…

Concept explainers

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.

Question

I need the answer as soon as possible

If design bond stress = 1.5 N/mm² is assumed, then the
development length of an Fe 500 HYSD bar of nominal
diameter 12 mm - which is fully stressed in tension - will be:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
30. An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E=69 GPa If Poisson's Ratio is 0.33, what will be the lateral strain? E=68 v=-e(lateral) e(axial)
A tensile force P Newton is applied gradually on a prismatic bar of length L m and areas of cross- section A m². The strain energy stored in the bar will be equal to
30. An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E = 69 GPa. If Poisson's Ratio is 0.33, what will be the lateral strain? E= 6/8 v = -E(lateral)/(axial)
A steel 0.6 inch×1.2 inch steel 90 m long is subjected to a 45 KN tensile load along its lenght.If poison's ratio is 0.3 Find: A. The deformation along its lenght. B. The deformation along its thickness. C. The defirmation along uts width. D. The lateral strain.
A steel with E = 29 000 ksi with a rectangular cross-section is bent over a rigid mandrel with R = 15 in as shown in the figure. If the maximum flexural stress in the bar is not to exceed the yield strength of 36 ksi, determine the allowable thickness h of the bar.
1.4-7 The data shown in the table below were obtained from a tensile test of high-strength steel. The test specimen had a diameter of 13 mm and a gage length of 50 mm (see figure for Prob. 1.4-3). At fracture, the elongation between the gage marks was 3.0 mm and the minimum diameter was 10.7 mm. Plot the conventional stress-strain curve for the steefor the steel and determine the proportional limit, modulus of elastics of elastic- ity (i.e., the slope of the initial part of the stress-strain,tress-strain curve), yield stress at 0.1% offset, ultimate stress, percent, elongation in 50 mm, and percent reduction in area. 'ess, percent area. TENSILE-TEST DATA FOR PROB. 1.4-7 Elongation (mm) 0.005 0.015 0.048 Load (kN) 5 10 30 50 0.084 60 0.099 64.5 0.109 67.0 0.119 68.0 0.137 69.0 0.160 70.0 0.229 72.0 0.259 76.0 0.330 84.0 0.584 92.0 0.853 100.0 1.288 112.0 2.814 113.0 Fracture
q7 A steel bar 2 m long, 20 mm wide and 15 mm thick is subjected to a tensile load of 30 kN. If Poisson's ratio is 0.25 and Young's modulus is 200 GPa, an increase in volume will be (b) 150 mm3 (d) 130 mm3 (a) 160 mm3 (c) 140 mm3
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0 and if the elastic mođulus and length of the bar is 200 GPa and 2 m respectively, calculate the elongation in mm of the bar corresponding to the maximum load it can support. (А) 5 (в) 2.5 1.25 D) 0.625
A bar of length 2.0m is made of a structural steel having the stress-strain diagram shown in the figure. The yield stress of the steel is 250 MPa and the slope of the initial linear part of the stress-strain curve (modulus of elasticity) is 200GPa. The bar is loadded axially until it elongates 6.5mm, and then the load is removed. How does the final length of the bar compare with its original length? (Hint: Use the concepts illustrated in figure below)