The composite bar of neglible mass is connected to two rods as shown in the figure. If the system is initially free, determine the temperature change that will cause a tensile stress of 60 Mpa in the steel rod. STEEL A=900 mm 3m t= 200 GPa ds - I1.7 x10 "/m°c 2m -6m/ Bronze 2 A= 1200 mm E- 83GPA & = 189 x10 "/m°C

The composite bar of neglible mass is connected to two rods as shown in the figure. If the system is initially free, determine the temperature change that will cause a tensile stress of 60 Mpa in the steel rod. STEEL A=900 mm 3m t= 200 GPa ds - I1.7 x10 "/m°c 2m -6m/ Bronze 2 A= 1200 mm E- 83GPA & = 189 x10 "/m°C

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter14: Material Selection

Section: Chapter Questions

Problem 8ETSQ

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
A rectangular steel block 250 mmx100 mmx80mm is subjected to axial loads as follows. 480 kN (tensile in direction of its length) 900 kN (tensile on 250mm x 80 mm faces) 1000kN (comp. on 250mm x100mm faces) taking E=200 GN/m2 and 1/m=0.25 find a). Change in dimensions (height, width and length) b). Change in volume of the block c). Volumetric Strain c). Values of N and K (Module of Rigidity and Bulk Modulus) for material of the block. d). Determine the volume difference if the temperature of block increased by 20K. (Take alpha steel = 11.7 x 10-6 / 0C ) e). Discuss the behavioral characteristic for given application Comparing the impact from given mechanical loadings and thermal loadings to the block.
Defferentiate the following terms; 1.Resilience and proof resilience 2.proof resilience and modulus of resilience B)A solid beam ABC circular in section has varying sections.portion AB is 6m in length and diameter of 250mm while portion BC is 2m in length and section diameter of 100mm.The beam is subjected to a sudden tensile load.if the maximum stress induced is 400MN/m^2.Determine the strain energy stored in the beam.Take E=200GN/m^2
The composite beam shown in the figure is simply supported and carries a total uniform load of 40 kN/m on a span length of 4.0 m. The beam is built of a southern pine wood member having cross-sectional dimensions 150 mm 250 mm and two brass plates of cross-sectional dimensions 30 mm 150 mm. (a) Determine the maximum stresses B and w in the brass and wood, respectively, if the moduli of elasticity are EB 96 GPa and Ew 14 GPa. (Disregard the weight of the beam.) (b) Find the required thickness of the brass plates so that the plate and wood reach their allowable stress values, saB 70 MPa and saw 8.5 MPa, simultaneously under the maximum moment. What is the maximum moment?
The composite beam shown in the figure is simply supported and carries a total uniform load of 90 kN/m on a span length of 4 m. The beam is built of a wood member having cross-sectional dimensions 150 mm x 250 mm and two steel plates of cross-sectional dimensions 50 mm × 150 mm. The moduli of elasticity are Es = 214 GPa and Ew = 11 GPa. (a) Determine the maximum stress in the steel. (Disregard the weight of the beam. Round to one decimal place.) (b) Determine the maximum stress in the wood. (Disregard the weight of the beam. Round to one decimal place.)
Determine the a.Stress at 167 kN loadin MPa b.Strain at 167 kN loadin mm/mm(expressed in scientific notation) c.Modulus of elasticityMPa d.Modulus of resiliencein N-mm/mm3 e.Modulus of toughnessin N-mm/mm3
A cantilever beam with a ‘T’ shaped cross-section is loaded with a distributed load as shown below.The intensity of the distributed load is 100N/mm. b = 6.25mm and c=6.25mm.Parameter Description Value UnitsL - Beam length 250 mma - Width of the flange 80 mmd - Height of the web 75 mmσ - Yield stress 250 MPaYou are tasked with ensuring the beam can withstand the applied loading. To do this you must:a) Calculate the centroid for the given cross-section. Your value of ?ത should be measured fromthe bottom of the section. Determine an expression for Q (statical moment of area) for thegiven shape. The expression(s) for Q should be in terms of the variable, y, measured from thebottom of the section. b) Create a graph of the shear and bending stresses at the fixed support (B) over the crosssection. The stresses should be plotted as a function of y, measured from the bottom of thesection.
A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress developed in the rod, in kN/m^2. Is the tensile or compressive? (b) compute the amount of elongation (in mm) in the steel rod caused by the applied load, (c) what will be the elongation (in mm) in the steel rod if the weight of the steel rod is included? Use density of the steel to be 7860 kg/m^3. Young's modulus of elasticity, E=200GPa. W=mg. Draw free body diagram of the steel rod.