If the allowable bearing stress for the material under the supports at A and B is σb = 610 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 4 in. by 4 in. The reactions at the supports are vertical. Assume w = 650 lb/ft, a = 10 ft, and b = 5 ft.

If the allowable bearing stress for the material under the supports at A and B is σb = 610 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 4 in. by 4 in. The reactions at the supports are vertical. Assume w = 650 lb/ft, a = 10 ft, and b = 5 ft.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.10P: Determine the allowable axial load Pallowfor a steel pipe column that is fixed at the base and free...

See similar textbooks

Similar questions

Determine the allowable axial load Pallowfor a steel pipe column that is fixed at the base and free at the top (see figure) for each of the following lengths: L = 2,6 m, 2.8 m, 3.0 m, and 3.2 m. The column has an outside diameter d = 140 mm and wall thickness t = 7 mm, (Assumed = 200 GPa and ( y= 250 MPa.)
Determine the allowable axial load Pallowfor a steel pipe column that is fixed at the base and free at the top (see figure) for each of the following lengths: L = 6 ft, 9 ft, 12 ft, and 15 ft. The column has an outside diameter d = 6.625 in. and wall thickness t = 0.280 in, (Assume E = 29,000 ksi and y= 36 ksi.)
Answer the following. If the allowable bearing stress for the material under the supports at A and B is σb = 820 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 5 in. by 5 in. The reactions at the supports are vertical. Assume w = 650 lb/ft, a = 10 ft, and b = 5 ft.
Consider the wooden member subjected to a tensile load P = 11.0 kN. Determine the magnitude of the normal force at the inclined section shown.
A composite section will be used to support a heavy axial load of P = 800 kN with a rigid plate at the top of the section. Determine the average compressive stress (MPa) in the brass section. Use h = 25mm.
The outside diameter of the steel pipe shown is 220 mm and its wall thickness is 6.0 mm. The upper bearing plate has the same width as the reinforced concrete beam it supports. The total load on the column by the reinforced concrete beam is 550 kN. Determine: A. The length L of the rectangular upper bearing plate if its width is 275 mm. and the average bearing stress between the steel plate and the reinforced concrete beam is not to exceed 6.2 MPa.
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 115 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 3 mm, and an allowable normal stress of 65 MPa. Assume x3 = 3.7 m, x2 = 1.5 m, and y; = 4.1 m, Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress
Problem 3 only, solve carefully, include the units in every step and draw the diagram. Thanks! In a 2.5 m cantilevered I-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress inbeam is 120 Mpa, determine theA. section modulus, in3 B. The base and height of the beam if the base is 75% of its height, mm
Load P is supported by levers ABC and DB as shown in the figure. Member DB is a truss member and has a square cross-section of 10 mm by 10 mm. If lever DB is made of 2014-T6 Aluminum, determine the maximum load P that can be applied. Take factor of safety 2. ? =100°
A stainless steel tube with an outside diameter of 50 mm and a wall thickness of 5 mm is used as a compression member. If the axial stress in the member must be limited to 384 MPa, determine the maximum load P that the member can support.
A steel [E = 25500 ksi] pipe column (1) with a cross-sectional area of A1 = 5.60 in.2 is connected at flange B to an aluminum alloy [E = 17500 ksi] pipe (2) with a cross-sectional area of A2 = 4.40 in.2. The assembly is connected to rigid supports at A and C. For the loading shown, determine the normal force in the steel pipe (1).
The piston of an automobile engine is held to the connecting rod by a wrist pin having an external diameter of 20 mm and internal diameter of 11 mm. The length of the bearing in the rod end is 25 mm and the bearing in each boss of the piston is 15 mm. The maximum load transmitted is 14.50 kN. (a) Determine the bearing pressure between the rod end and the wrist pin. (b) Compare the maximum bending stress in the pin, assuming that it is a simple beam with a uniform load. Please solve completely ?