Answered: The three suspender bars are made of…

The three suspender bars are made of steel and have equal cross-sectional areas of 450 mm?. Determine the average normal stress in each bar if the rigid beam is subjected to the loading shown.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Determine the largest intensity w of the distributed load that the member can support if the…

A: The free-body diagram of the beam can be drawn as follows, The reactions at A and B respectively…

Q: If the cross section of the femur at section a–a can be approximated as a circular tube as shown,…

A: Considering the equilibrium of femur,

Q: The rotor shaft of the helicopter is subjected to the tensile force and torque shown when the rotor…

Q: The rigid beam is supported at its ends by two A-36 steel tie rods. The rods have diameters dAB =…

A: Draw the free-body diagram of the beam.

Q: Determine the torsional stress in the thin-walled tube as shown:

Q: The 2-Mg concrete pipe has a center of mass at point G. If it is suspended from cables AB and AC,…

A: Given data as per question Diameter of cable AB = 12mm Diameter of cable AC = 10mm Mass = 2 Mg =…

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings. Determine the…

A: The torque acting at A is given as : Polar moment of inertia is calculated as :

Q: Determine the stress in the cable BC if the mass of the cylinder is 250 kg. The cross sectional area…

Q: ) If the load has a weight of 600 lb, determine the maximum normal stress developed on the cross…

A: An internal resisting force which is applied by the molecules of the object so that the shape of the…

Q: The screw of the clamp exerts a compressive force of 500 lb on the wood blocks. Determine the…

A: Area at section (a-a) Moment of inertia at section (a-a)

Q: The beam is subjected to the load at its end. Determine the maximum principal stress at point B.

A: Determine normal stress due to axial load Due to shear load there will be bending moment at B…

Q: The assembly consists of three stainless 304 steel alloy rods (G = 193 GPa) and a rigid cap G. If…

Q: The beveled gear is subjected to the loads shown. Determine the stress components acting on the…

A: The forces and torques at point B are shown as, On using equilibrium of forces in x, y, and…

Q: The beam is supported by two rods AB and CD that have cross-sectional areas of 12 mm2 and 8 mm2,…

Q: Qi: The shaft is hollow from A to B and solid from B to C. Determine the maximum shear stress…

Q: The shaft is hollow from A to B and solid from B to C. Determine the maximum shear stress in the…

Q: The member consists of two plastic channel strips 0.5 in. thick, glued together at A and B. If the…

A: Draw the free body diagram.

Q: The shaft is supported by a thrust bearing at A and a journal bearing at B. If P = 20 kN, determine…

A: The absolute stress in the above said problem is to determined using the Shear formulae. This…

Q: The rod has a diameter of 1 in. and a weight of 10 lb>ft. Determine the maximum torsional stress…

A: diameter of rod (d) = 1 in. weight of rod (w) = 10 lb-ft the FBD of the cut segment of the rod is…

Q: If column AB is made from high strength precast concrete and reinforced with four 3 4 in. diameter…

A: Understand that the 4 steel rods and the concrete block forms a parallel connection system. Let PS…

Q: Determine the maximum normal stress (in MPa) developed in the bar when it is subjected to a tension…

Q: The assembly consists of a solid 15 mm diameter rod connected to the inside of a tube using a rigid…

Q: The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. If P = 5…

Q: Determine the maximum average shear stress developed in the 30-mm-diameter pin.

A: Given Data: The diameter of pin is d = 30 mm. Force in x-direction is Fx = 40 kN. Force in…

Q: The 200-mm-diameter aluminum cylinder supports a compressive load of 300 kN. Determine the average…

Q: The tank of the air compressor is subjected to an internal pressure of 90 psi. If the inner diameter…

A: Write the given data: Understand that the stress generated at point A will be the tangential stress…

Q: The rod has a diameter of 1 in. and a weight of 15 lb>ft. Determine the maximum torsional stress…

A: Given: The diameter of rod is D = 1 in. The weight of the rod is M = 15 lb/ft. The length of the…

Q: The lever is attached to the shaft A using a key that has a width d and length of 25 mm. If the…

A: Given data: Vertical force (Fy) = 200 N (downwards) (perpendicular to the…

Q: Force F=4 kN and length a - 5 m. The radius of the bar is 0.09 m. Determine • the internal loading…

A: Given:F=4 KNa=5 m r=0.09mThe force F acting can be replaced by torque(T) and a upward force…

Q: he shaft is loaded with torque and force acting at location B and C. Given the diameter of 1 in.,…

Q: Determine the average normal stress on the cross section. Sketch the normal stress distribution over…

A: Given: The magnitude of the force acting on the cross-section is F= 300 kN. The inner radius is…

Q: Determine the normal and shear stress on section a-a that passes through the centerline at point C…

Q: The beam is supported by two rods AB and CD that have cross-sectional areas of 12 mm2 and 8 mm2,…

A: Applying the equilibrium condition,…

Q: The assembly consists of a solid 15 mm diameter rod connected to the inside of a tube using a rigid…

Q: he two members used in the construction of an aircraft fuselage are joined together using a 30°…

A: ΣFy = 0 FN – 2*1000*sin30 = 0 FN = 1KN ΣFx = 0 -FT + 2*cos30 = 0 FT = 1.732KN

Q: The central pillar B of the system has a length of 124.7mm in the beginning, while the a and c…

A: LB=Original length of center post =124.7 mmA=Cross sectional area of each post =400 mm2=400×10-6 m2

Q: The block is subjected to the eccentric load shown. Sketch the normal-stress distribution acting…

A: Given Applied load = 150 kN To find The normal stress distribution

Q: al stress (in MPa) developed in the bar when it is subjected to a tension of P = 12 kN.

Q: The thin-walled pipe has an inner diameter of 1.2 cm and a thickness of 0.06 cm. If it is subjected…

A: Determine the axial and hoop tension as follows.

Q: The bars of the truss each has a cross-sectional area of 780 mm?. Determine the average normal…

Q: If the load has a weight of 2940 N, determine the magnitude of the maximum compressive normal stress…

Q: If the load has a weight equivalent to 5 kN, determine the maximur hormal stress on the cross…

A: Given Data Load is :P=5 kN=5000 N Radius of circle is :r=2 cm=20 mm Distance of CD is : LCD=50…

Q: The 0.97 in diameter rod is subjected to the loads shown. Determine the normal and shear stress at…

A: To find: The normal and shear stress at point B. Given: The diameter of the rod is d=0.97 in.…

Q: The bar has a constant width of 35 mm and a thickness of 10 mm. Determine the maximum average normal…

Q: The elbow of the pipe has an outer radius of 0.75 in. and an inner radius of 0.63 in. If the…

A: Given, M= 25 lb.in

Q: Two spanners are used to tighten the pipe. If P =200 N is applied to each spanner, determine the…

A: Given:P=200 ND=25 mmd=20 mm

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

The three suspender bars are made of
steel
and have equal cross-sectional areas of 450 mm?.
Determine the average normal stress in each bar if the rigid
beam is subjected to the loading shown.
A
В
C
80 kN
2 m
50 kN
D
E
-1 m-
+1m-
1m-1 m-|

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the bolt is subjected to a compressive force of P = 20 kN, determine the average normal stress in the steel and the bronze. Est = 200 GPa, Ebr = 100 GPa.
The rigid beam is supported by the three suspender bars. Bars AB and EF are made of aluminum and bar CD is made of steel. If each bar has a cross-sectional area of 450 mm2, determine the maximum value of P if the allowable stress is (sallow)st = 200 MPa for the steel and (sallow)al = 150 MPa for the aluminum. Est = 200 GPa, Eal = 70 GPa.
The A-36 steel column, having a cross-sectional area of 10500 mm2, is encased in high-strength concrete as shown. If an axial force of 300kN is applied to the column, determine the compressive stress in the concrete and in the steel. Es = 210GPA and Econc = 29 GPA.
The center post B of the assembly has an original length of 123 mm, whereas posts A and C have a length of 127 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress (in MPa) post A. The posts are made of aluminum and have a cross-sectional area of 423 mm2 Ealuminum = 70 GPa.
The two cylindrical rod segments are fixed to the rigid walls such that there is a gap of 0.01 in. between them when T1 = 60°F. Each rod has a diameter of 1.25 in. Determine the average normal stress in each rod if T2 = 400F, and also calculate the new length of the aluminum segment. Take aal = 13(10-6)>°F, Eal = 10(103) ksi, (sY)al = 40 ksi, acu = 9.4(10-6)>°F, (sY)cu = 50 ksi, and Ecu = 15(103) ksi
The center post B of the assembly has an original length of 122 mm, whereas posts A and C have a length of 126 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress (in MPa) post A. The posts are made of aluminum and have a cross-sectional area of 403 mm2. Ealuminum = 70 GPa. The correct answer is 887.66682. Show solution pls.
The steel pipe is filled with concrete and subjected to a compressive force of 75 kN. Determine the average normal stress in the concrete due to this loading. The pipe has an outer diameter of 60 mm and an inner diameter of 50 mm. E_s=200 GPa, E_c=24 GPa
Determine the maximum normal stress (in MPa) developed in the bar when it is subjected to a tension of P = 12 kN.
The two members used in the construction of an aircraft fuselage are joined together using a30° fish-mouth weld. Determine the average normal and average shear stress on the plane ofeach weld. Assume each inclined plane supports a horizontal force of 4 kN.
The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T1 = 50°F, determine the average normal stress in each member when T2 = 120°F. Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in2.
The steel bracket below is used to connect the ends of two cables. If the applied force P=1.50kip, determine the maximum normal stress (in ksi) in the bracket. Assume the bracket is made from a rod having a diameter 1.5in.
The bar has a cross-sectional area of 400(10−6) m2. If it is subjected to a uniform axial distributed loading along its length and to two concentrated loads, determine the average normal stress in the bar as a function of x for0 6 x … 0.5 m.