If the settling time (5% criterion) and the damping ratio of a 2nd order system are given, find the location of the 2 closed-loop poles on the s-plane. Type a, b, c or d. 手,下半手 t; = 7 sec and zeta = 0.6. jw s-plane ja s-plane jw s-plane ja s-plane j0.571 X.---Lj2.37 X- j0.57 X- j0.75 -0.429 -2.47 -1.04 -1.28 X X (а) (b) (c) (d) Answer:

If the settling time (5% criterion) and the damping ratio of a 2nd order system are given, find the location of the 2 closed-loop poles on the s-plane. Type a, b, c or d. 手,下半手 t; = 7 sec and zeta = 0.6. jw s-plane ja s-plane jw s-plane ja s-plane j0.571 X.---Lj2.37 X- j0.57 X- j0.75 -0.429 -2.47 -1.04 -1.28 X X (а) (b) (c) (d) Answer:

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.59P

See similar textbooks

Similar questions

Assume that the system recorded by the block diagram is reliable. a) Determine the position constant, kp, of velocity, kv, and of acceleration, ka, of the system. b) Determine the steady-state errors for a magnitude 5 input in step, ramp, and parabola, respectively.
5/The Voltage Regulation of a Transmission Line (in the simulator) depends on which parameter/s? A. Both the Transmission Line Resistance and Inductance B. The Transmission Line Shunt Capacitance only C. The Transmission Line Inductance only D. The Transmission Line Resistance only
If the pole is located at the origin of the s plane, the response is in the form of a: a. damp exponential b. exponential rise c. sinusoid d. constant What characterizes an unstable system? a. poles at the origin b. poles with negative real part c. poles with positive real part d. poles without real part Routh’s stability criterion will provide the number of: a. RHP b. poles c. LHP d. imaginary poles
a)We have a two-wire overhead transmission line, powered by a constant voltage source of 700 V. The values for the inductance of the conductors are 2.348x10-3 H/km and the capacitance values are 6.325x10-9 F/km. Assuming an ideal (no loss) line and its length at 130 km, determine the natural impedance of the line. b) What is the transient phenomenon in a transmission line? As an example of its causes.
Given the asynchronous circuit, determine the map Q1, Q2, Z, transition table, and flow table.
In order for the closed loop system, whose block diagram is given below, to be stable, the parameters K1 and K2 must be determined. Calculate the values it will take. Draw the graph of the stable region in the K1-K2 plane. (Hint: Routh-Hurwitz use the method)
The poles of a system are:P1=1, P2=(2+7), P3=(3+7), P4=(4+7), and P5=(5+7)(i) Draw the system in complex z-plane(ii) Determine the possible ROCs(iii) Comments on the causality and stability for each ROC
1- Please, Derive Equation of Motion for the 2DOF system with Harmonic force due to the Shaker in the Magnetostrictive Energy Harvesting. Note: I want EOM in Matrices form to get Natural frequencies and mode shapes + Steady-State Response of Spring-Mass System
A) Sketch the complex plane and locate poles for 2 cases: 2 Second Order underdamped systems where both systems have the same settling time, but system #1 has a larger overshoot. B) Sketch the time response for each system in part A to a unit step input. Show clearly which system is 1 and 2. Show the relative values of the overshoot for both systems, the overshoot time, damped natural frequency and time to steady state .
Explain the concept of grid inertia and its significance in maintaining stable frequency in power systems with high renewable energy penetration.
What is the effect on %VR value if taken at half-load lagging pf? Justify and explain briefly your answer on one(1) sentence.
Derive the full solution to the driven LRC circuit shown below using complex exponentials. Start withKirchhoff’s rule for the loop and assume a complex V (t) = V0eiωt (where by convention V0 is real) andassume that I(t) = I0eiωt where I0 is a general complex number (which can be written quite generallyas I0 = |I0|e−iδ), and where one gets physical answers at the end by taking the real part of thecomplex answers. Find an algebraic complex expression that expresses the sum of the voltages. Solve this expression directly using algebra, no pictures of “phasors” really required. Factor out the solution to obtain|I0|, δ, Z (the complex impedance), and the voltages across each element as a function of time.