Answered: If there is a net force of 250N [W30S]…

If there is a net force of 250N [W30S] what force would you need to apply in order for the system to be in equilibrium? (a) 250 [E30N] (b) 250 [W30N] (c) 250 [E30S] (d) 250 [S30W]

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 1PQ: What Is Static Equilibrium? Problems 13 are grouped. 1. C A ball is attached to a strong,...

See similar textbooks

Related questions

Q: Determine the tension at the cable TAB and TAC in the system below at equilibrium. 3 m C 4 m A 4.5…

Q: The forces on the gusset plate of a joint in a bridge truss act as shown. Determine the value of F…

Q: The following setup of masses is hung (las) to a fixed ceiling as shown in the figure below. If M, =…

A: Here, a figure is given, showing a setup of masses hung from the ceiling. It is also given that M1…

Q: The system in the figure is in equilibrium. A concrete block of mass 238 kg hangs from the end of…

Q: The wooden sign is supported by three chains attached to the ceiling (AC, AB & AD) If the tension in…

A: According to guidelines we are suppose to do only three part from multipart questions. Kindly repost…

Q: The system in the figure is in equilibrium. A concrete block of mass 289 kg hangs from the end of…

Q: The system in the figure is in equilibrium. A concrete block of mass 327 kg hangs from the end of…

Q: When the structure shown below is supported at point P, it is in equilibrium. Find the magnitude of…

A: Given, The system is in equilibrium about Point P.

Q: Tweedledum and Tweedledee are carrying a uniform wooden board that is L = 3.00 m long and has a…

A: W = 160N L = 3 m F1 = 60 N

Q: F FB A CG B A mg = Assume FA is down and the 20 kg board is 5 meters long. The board is in static…

A: Dear student When objects are in static equilibrium, the net force as well as net torque on it is…

Q: The boom in the figure is 2m long and weighs 100 N. If the 800N load is suspended 50cm from the end,…

Q: A 10-m long homogenous beam with a weight of 50N is divided into 10 equal parts (1 m each) as shown…

Q: A 10 m ladder with a mass of 15 kg leans against the wall. If the ladder is in static equilibrium,…

A: Given. m = 15 Kg L = 10m Concept - Force balancing in all directions.

Q: The system in the figure is in equilibrium. A concrete block of mass 203 kg hangs from the end of…

Q: A uniform platform with mass M=30kg and length L=15m is placed on two supports as shown. The…

A: A mass of a uniform platform,

Q: = (Static Equilibrium) An 8-m long horizontal boom with a mass of 100 kg (w 981 N) supports a 2000…

Q: A uniform beam of length L= 0.18 m and mass mb=0.83 kg is pinned at one end to a vertical wall. A…

A: The weight of the beam acts on the midpoint of the beam at L/2, in downward direction. The tension…

Q: The system in the figure is in equilibrium. A concrete block of mass 180 kg hangs from the end of…

Q: A 500g meter stick is supported at its 0 cm and 100 cm marks by two strings attached to the ceiling.…

A: The vertical forces acting on the stick are the upward tension forces T1 and T2 and the downward…

Q: An object that weighs 1180 N rests on a lever at a point 0.390 m from a support. On the same side of…

A: Given: P = 1180 N x = 0.390m

Q: The system in the figure is in equilibrium. A concrete block of mass 325 kg hangs from the end of…

Q: 11) A horizontal, uniform bar of mass 26 kg and length 3.0 m is hinged to a wall on its left side…

Q: For the equilibrium system shown below, determine the following: 1) Unit vector for the force vector…

A: NOTE- As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost…

Q: The system in the figure is in equilibrium. A concrete block of mass 185 kg hangs from the end of…

Q: The system in the figure is in equilibrium. A concrete block of mass 327 kg hangs from the end of…

Q: A uniform beam is 5.0 m long and is supported as shown in the figure. At the center of the beam, a…

Q: The system in the figure is in equilibrium. A mass of 225 kg hangs from the end of the uniform mass…

A: (a) The figure shows the forces acting on the strut. (b) Since the strut is in equilibrium, the net…

Q: A uniform platform with mass M=30 kg and length L=15 m is placed on two supports as shown. The…

Q: Current Attempt in Progress The system in the figure is in equilibrium. A concrete block of mass 248…

Q: 53° 5 m A uniform 80N beam that is 5 m long is attached to a wall by a cable as shown in the figure.…

Q: The system in the figure is in equilibrium. A concrete block of mass 333 kg hangs from the end of…

Q: The system in the figure is in equilibrium. A concrete block of mass 181 kg hangs from the end of…

Q: Fac = 60 lbf E 25 6 ft 15* 24 W = 215 Ibf

A: Force is a vector quantity defined as the rate of change in the momentum of an object as defined by…

Q: A uniform meterstick is supported at the 50 cm mark. A 25N weight is placed at the 10 cm mark. Where…

A: Rotation is when body revolves around a fixed axis. All the particles of body go circular motion. A…

Q: A uniform beam with a mass of 125 kg and a length of 6.00 meters rests on a fulcrum, which is…

A: (a) The FBD of the given situation can be drawn as shown below: Here, F, W, and T are the…

Q: A uniform beam of length 12.0 m and weight 690 N is connected to a wall by a bolt, and is supported…

Q: A uniform bar weinghing 60N has a lenght of 4M and is supported at its end by string. A load W=200N…

Q: SAQ 1.1 1. A nonuniform bar 2 m long is horizontal and is in a state of equilibrium when supported…

A: Dear student When any system is in equilibrium, the net force as well as the net torque on it is…

Q: A force F making an angle of 30° with the horizontal maintains a box with mass m = 8 kg in static…

A: mass = 8 kg θ = 30og = 10 ms2

Q: You place a 15 kg brick 0.5 m to the left of the fulcrum. Where on the right side would you place a…

A: Given data: Mass on left side (m1) = 15 kg Distance from fulcrum (r1) = 0.5 m Mass on right side…

Q: 50 N 0.20 L 60 N 0.60 L 80 N 30 0 70

Q: The system in the figure is in equilibrium. A concrete block of mass 307 kg hangs from the end of…

Q: 1. The horizontal beam AB shown has a mass of 2.04 kg with center of gravity at its center. Find: A…

A: Consider the known data as below. Mass at the middle of the beam, m=2.04 kg Gravity, g=9.81 ms2…

Q: In the force table, these have the same magnitude but directly opposite in direction.…

A: An equilibrant force is a force which brings a body into mechanical equilibrium.

Q: My book has the answers as a) 10N b) 196N But I can't figure out the proper way to work it out. I…

Q: (8c12p13) Forces F1, F2, and F3 act on the structure depicted in the figure, shown in an overhead…

A: Given a = 1.9 m, b = 2.7 m, C = 1.05 m, F1 = 24.10 N, F2 = 12.85 N, and F3 = 4.65 N. To Find Fh,…

Concept explainers

Rotational Equilibrium And Rotational Dynamics

In physics, the state of balance between the forces and the dynamics of motion is called the equilibrium state. The balance between various forces acting on a system in a rotational motion is called rotational equilibrium or rotational dynamics.

Equilibrium of Forces

The tension created on one body during push or pull is known as force.

Question

If there is a net force of 250N [W30S] what force would you need to apply in order for the system to be in equilibrium? (a) 250 [E30N] (b) 250 [W30N] (c) 250 [E30S] (d) 250 [S30W]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A uniform platform with mass M=30kg and length L=15m is placed on two supports as shown. The distance between the supports is a=6m and F=340N is applied as shown with distance b=4m. The system is in static equilibrium. a) Find Normal force FN1 in Newtons. b) Find Normal force FN2 in Newtons.
A uniform beam of length 12.0 m and weight 690 N is connected to a wall by a bolt, and is supported by two cables. Cable 1 makes an angle of 25.0 Degrees with the beam, is attached 5.00 m from wall, and has a tension of 312 N. Cable 2 makes an angle of 39.0 Degrees with the beam and is attached to the end of the beam. The system is in static equilibrium. What is the tension in cable 2?
The system in the figure is in equilibrium. A concrete block of mass 349 kg hangs from the end of the uniform strut of mass 52.2 kg. For angles φ = 20.6° and θ = 62.6°, find (a) the tension T in the cable and the (b) horizontal and (c) vertical components of the force on the strut from the hinge.
The system is in equilibrium. A concrete block of mass 225 kg hangs from the end of the uniform strut of mass 45.0 kg. A cable runs from the ground, over the top of the strut, and down to the block, holding the block in place. For angles f = 30.0° and u = 45.0°, find (a) the tension T in the cable and the (b) horizontal and (c) vertical components of the force on the strut from the hinge.
Two ladders, 4.00 m and 3.00 m long, are hinged at point A and tied together by a horizontal rope 0.90 m above the floor. The ladders weigh 480 N and 360 N, respectively, and the center of gravity of each is at its center. Assume that the floor is freshly waxed and frictionless. (a) Find the upward force at the bottom of each ladder. (b) Find the tension in the rope. (c) Find the magnitude of the force one ladder exerts on the other at point A. (d) If an 800-N painter stands at point A, find the tension in the horizontal rope.
One end of a 2.00 m uniform meter stick is placed against a vertical wall. The other end is held by a lightweight cord that makes an angle θ with the stick. The coefficient of static friction between the end of the meter stick and the wall is 0.530. What is the maximum value that θ can have if the stick is to remainin equilibrium?
Two ladders, 4.00 m and 3.00 m long, are hinged at point A and tied together by a horizontal rope 0.90 m above the floor. The ladders weigh 600 N and 450 N, respectively, and the center of gravity of each is at its center. Assume that the floor is freshly waxed and frictionless. (a) Find the upward force at the bottom of each ladder. (b) Find the tension in the rope.
A uniform beam of length L= 0.18 m and mass mb=0.83 kg is pinned at one end to a vertical wall. A rope attaches the other end of the beam to the wall above the pin and holds the beam in a horizontal position. The rope makes an angle θ= 30o with respect to to the wall. What is the magnitude of the tension in the rope?
An axial pull of 1.5 kN is acting on a bar of consisting two equal lengths as shown but of diameter 10cm and 20 cm respectively. What will be the stresses in the two sections respectively in N/mm2? A. 0.153 and 0.0036 B. 0.290 and 0.046 C. 0.190 and 0.0046 D. 0.124 and 0.124
If M1=M2=100g. What must be the value of M3 to keep the system below balanced disregard the mass of the rigid bar. a) 359.33 g b) 366.67g c) 23.33g What is the correct answer
overhead view of a rigid rod that turnsabout a vertical axle until the identical rubber stoppers A and B are forced against rigid walls at distances rA = 7.0 cm and rB = 4.0 cmfrom the axle. Initially the stoppers touch the walls without beingcompressed.Then force of magnitude 220 N is applied perpendicularto the rod at a distance R = 5.0 cm from the axle.Find the magnitudeof the force compressing (a) stopper Aand (b) stopper B.
The wooden sign is supported by three chains attached to the ceiling ( AC,AB,AD). If the tension in AB= 100 lbf and AC=65 Lbf, determine the tension in AD and the weight of the sign in equilibrium. 1 Determine the x component of the force AB: ABx= __lbf 2 Determine the Y component of force AB:ABy=__lbf 3 Determine the x component of force AC:ACx=__lbf 4 Determine the y component of the force AC:ACy =__lbf 5 Determine the magnitude of the force AD =__lbf 6 Determine the weight of the sign=__lbf