Importance of Dual side working system using scotch yoke mechan

Q: Position and velocity and acceleration analysis for Scotch yoke mechanism Using loop equation

A:

Q: tollowing mie by mahmg tables where possible: Oct G-2)+1)

A:

Q: Type of Mechanism

A: As given in question we have to match the following mechanism; hence; (P) SCOTT (Q) Geneva mechanism…

Q: Describe one of control section component which is used to operate double acting cylinder of having…

A: The double cylinder having 3 position and 4 ports is given.

Q: Describe the principle of operation of a tilting-pad thrust bearing

A: These types of bearings are used for transferring high axial loads from rotating shafts with lesser…

Q: Define the following, Joint. Link. Joint space. Actuator space.

A: Joint: A point where two or more than two links are connected is known as joint. Link: It is a…

Q: Which fastener type would require the smallest positional tolerance (if all other design parameters…

A: In this problem, it is asking about the type of fastener that requires the positional tolerance to…

Q: what is a flanged coupling ?

A: Coupling : It is mechanical device which connects two shafts for power transmission from the driving…

Q: 2. Explain the advantage and disadvantages of DuFort-Frankel and Crank- Nikolson methods.

A: In numerical analysis, the Crank–Nicolson method is finite difference method used for numerically…

Q: Explain the installation procedures of a flexible coupling

A: given; explain the installation procedures of a flexible coupling.

Q: A double-acting cylinder is to be used to emboss plastic rulers. The cylinder may only extend when…

A: as the press tool is the device in which the sheet metal components are are produced in large volume…

Q: Within certain limits, a ------- coupling allows relative rotation and variation in the alignment of…

A: Type of coupling which allows various motion need to be answered

Q: Electro-pneumatics Sequential Circuit Problem: Initial position all cylinder are retracted. Pressing…

A: Given : Cycle Operation: Cylinder A extend and hold the work piece. Cylinder B extend for 5 secs.…

Q: What is the degree of freedom of the mechanism?

A: A mechanical system's degrees of freedom (DOF) are the number of independent characteristics that…

Q: The company has two diesel- powered standby generators, both of which are capable of supplying…

A:

Q: Using a double-acting cylinder a work piece is removed and tipped onto conveyor belt. The operation…

A: Solution: The Pneumatic circuit Diagram with ISO symbols is shown below:

Q: What are the advantages of cold-side ESPs over hot-side ESPs?

A: Electrostatic precipitators(ESP)  are devices which are used to remove dust and smoke particles from…

Q: How many primary joints are there in this mechanism? 22.9 22.9 /D E 4.5 typ.

A: Primary Joints include pins, sliders and other elements that allow pure rotation or pure linear…

Q: For the manufacture of a pipe wrench would you select: a. Fe-0.4%C steel b. Fe-0.4C steel abs case…

A: Pipe wrenches are available in different sizes from 3 inches to 48 inches or larger. A pipe wrench…

Q: What is normal operating conditions?

A: Normal operating condition refers to the condition at which any machine can work without any fatigue…

Q: What does a worm screw pulley do and what is it used for? Explain the working system in detail.

A: The worm screw is the driving gear in the worm gear arrangement. The worm gear is the arrangement of…

Q: stiffness (in N/m) of the required mounting pad

A: Given; A precision instrument package m= 1 kgSurface vibrating at= 60 HzIsolation is designed with…

Q: 4. What are the advantages and disadvantages of using the Wet Mount technique?

A: advantage: Wet-mount: A microscope slide specimen is suspended in a drop of liquid located between…

Q: When rope drive is preferred?

A:

Q: 4.A. What type of seal system is constructed of a hard brittle material and is often used in a pump…

A: 14.A.What type of seal system is constructed of a hard brittle material and is often used in a pump…

Q: Define the difference between an integrated and a nonintegrated antilock breaking system

A:

Q: First pulley ley

A: The tensions in the rope on the sides of pulley will be different due to rotational inertia. Three…

Q: The schematic diagram of Assembly fixture for greasing of roller bearings is shown in Figure 4.…

A:

Q: What method should be used when connecting two shafts which has constant angular rotation amounts…

A: Two shafts can be connected by either by rigid or flexible coupling.  Rigid shaft coupling is used…

Q: On vehicles that use hydraulic servo with graduated servo rods, grooves on the end of the rod…

A: The graduated servo cylinders are used where very precise linear travel is used.

Q: Large cars with long drive shafts often use a double-U-joint arrangement called a __ .a. Spicer…

A: A universal joint is a mechanical connecting device that is used between the rotating shafts and the…

Q: The clamping of a work piece is to be controlled by either of two Push buttons. A further push…

A:

Q: Types of couplings

A:

Q: Explain any one type of coupling which can be used to connect two aluminum alloy shafts when there…

A: Oldham Coupling is used to connect the two shafts which are in lateral misalignment.

Q: ASAP

A:

Q: Explain the Automatic hammer: basic components and operation.

A: An automatic hammer used to find the standard penetration test counts for geotechnical projects. The…

Q: NLESS OTHERWISE SPECIFIED : MATERIAL: FORGED STEEL NAME: LATCH BOLT 9-9 OLERANCES +/-.006 FINISH:…

A: 12. Maximum dimension = 0.623 + 0.003 = 0.626  13. Minimum dimension = 0.623 - 0.003 = 0.620 10.…

Q: List of main equipment required to manufacture the connecting rod assembly, number of equipment…

A: Connecting rod  The component of an engine that links the piston to the crankshaft, called a…

Q: What are couplings? When are they used?

A: Couplings: It is a mechanical device that connects two shaft which is used to transmit power from…

Q: Forcesin Cable BA d ch-7 lom 2om

A: Given: W=100 kg

Q: Differentiate between a fast and loose pulley.

A: Difference between fast pulley and loose pulley is given below.

Q: what type of analysis is done in connecting rod Linear static analysis or dynamic analysis

A: Given Connecting rod To find Type of analysis

Q: Draw and design a bushed pin type flexible coupling

A: The Answer is below

Q: List the pros and cons of a compression spring ping pong ball launcher

A: The pros and cons are listed herein:

Q: What is another name for a trigger wheel?   reluctor   interrupter ring   timing wheel…

A: Generally trigger wheel also known as reluctor. The teeth on the trigger wheel equal to the number…

Hydronics