What is another name for a trigger wheel?   reluctor   interrupter ring   timing wheel   Hall-effect switch

Q: Which of the following is not a type of adjustment to a dozer blade? Camber Pitch Tilt Angle

A: Option (a)  camber

Q: List the missing parts Reciprocating motion Crank mechanism

A: A connecting rod in the engine is used to connect the piston with the crank rod. one end is attached…

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is O…

A: The correct maintenance procedure for gib adjustment on the lathe machine Adjust the gib to new…

Q: You are to draw suitable hydraulic circuit based from the given figure. MAIN RELIEF STATIONARY VALVE…

A: Given : To find : Hydraulic circuit

Q: True or False: Holding down the <Shift> key during the CHAMFERcommand allows it to draw fillet…

A: By holding the Shift key before selecting the second object when using a CHAMFER command, the…

Q: Drive Shaft G-Codes programming process

A: Given question: Drive Shaft G Code programming process. The given question is related to…

Q: What types of traction machines are used for hoisting elevators?

A: Given Data→ Traction machines Hoisting elevators

Q: triple beam balance?

A: Explanation given below.

Q: True or False: Polar tracking can be set to detect any angle

A: To display the alignment paths defined by the polar angles, polar tracking can be used. In 3D-views,…

Q: Explain in detail about the two types of shaft alignment, soft foot, and indicator sag.

A:

Q: 2. Technician A says that load-carrying ball joints should always have some play in them. Techni-…

A: The ball joints basically serve as the pivot point between the tyre and the suspension in an…

Q: During drilling operation, work piece must be held in vice. Select one: True False

A: Given Statement : During drilling operation, work piece must be held in vice. Select one: True…

Q: An universal coupling commonly used in shafts that transmit rotary motion Select one: True False

A: An universal coupling commonly used in shafts that transmit rotary motion Answer: True

Q: rest position to the upright unstable equilibrium position.

A: Introduction The truck pendulum framework is an ordinary benchmark issue in the control field. It is…

Q: the speed can be positive or negative false true

A: Speed is a scalar quantity. it has no direction so, speed can be positive or zero. it cannot be…

Q: The connecting rod journal is also called the __ .a. balancer shaftb. vibration damperc.…

A:

Q: What is sensitiveness of a governor?

A: To explain: The sensitiveness of a governor. Explanation: Sensitiveness of a governor: The device…

Q: rank mech

A: given: what is the inverson of double slider crank mechnism?

Q: Fulcrum can be only  located at one end of the lever.

A: Fulcrum can be only  located at one end of the lever.

Q: What are the inversion of single slider mechanism when connecting rod is fixed?

A: Given: When one link is fixed in a mechanism it will work like a machine and gives the directional…

Q: torque to rotate disk underwater

A: Torque, also known as the moment of a force, is the propensity of a force to spin the body to…

Q: What type of drill machine can be used in hand-held mode?     a)Micro drill b)Upright drill c)Radial…

A: Given data : Drill machine Hand-held mode

Q: The Mobility of a four bar change point mechanism is O 1 O 3 O 4

A: Consider : - The number of links is l. The number of lower pair is j. The number of higher pair is…

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is On…

A: The engine lathe is a high-precision machine tool that needs to be treated with care. The lathe's…

Q: Where are the application of slider crank mechanism?

A: This question is based on the concept of slider crank mechanism.

Q: 4. What are the advantages and disadvantages of using the Wet Mount technique?

A: advantage: Wet-mount: A microscope slide specimen is suspended in a drop of liquid located between…

Q: 5 inch dia. shafts coupling to connect the equipment shafts. Note: use 4 bolts only nstructions:

A:

Q: Creo Software to perform the assembly operation for a shaft and hole system. Hint: you can choose…

A: we have to demonstrate the assembly feature in creo parametric

Q: In Auto-CAD object snap is used to pick accurately--- of a line. End point Mid point Nearest point

A: In Auto-CAD object snap is used to pick accurately-of a line. O End point O Mid point ONearest point

Q: Importance of Dual side working system using scotch yoke mechan

A:

Q: Mobility of a triple crank mechanism is one O four O two three

A: Mobility of triple crank mechanism is one

Q: If an actuator fails to move, name five possible causes.f an actuator has slow or erratic motion,…

A: Actuator is a component of a machine which capable in moving in a controlled mechanism.It consist of…

Q: of the link is havi

A: given: Which of the link is having to and fro movement in the engine mechanism? crank…

Q: 3. What is the difference between Turn Coordinator and Turn and Slip Indicator?

A: the turn and slip indicator and turn coordInator are very similar.in fact , the turn and slip…

Q: What is another name for the diaphragm spring?

A:

Q: How would I design a quick return crank-rocker mechanism with a rocking angle of 70 degrees and a…

A: Given that, Rocker angle, α=70°Time ratio, Tr=αβ=1.2…

Q: Chuck key requires lubrication maintenance. Select one: True False

A:

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is The…

A: Given: The wrong maintenance procedure followed while performing gib adjustment on a lathe machineis

Q: Applying finger pressure on the belt near the pulley end is the correct method to check the tension…

A:

Q: haft G-Codes programming process (sumerik)

A: CNC programmers increasingly face special tasks that take them to the limits of classic (DIN 66025)…

Q: Which of the following wrenches is the best choice fortorquing a bolt?a. Open-endb. Box-endc.…

A: When it comes to bolted joints, orquing is the most popular method of achieving fastener preload.…

Q: What type of axle housing resembles a banjo?

A: Given Data : Banjo

Q: The copper head hammer is used for releasing hold pin in the chuck. Select one: True False

A: The copper hear hammer is a hammer in which striking portion of the hammer (or head) are…

Q: 127) Technician A says a special tool can be used to depress the servo spring for servo disassembly.…

A: According to Technician A,  A special tool can be used to depress the servo spring for servo…

Q: preload on screws for reused connections is lower than permanent connections Select one: O True O…

A: preload on screws for reused connections ,non-permanent connections is 75 percent of proof load.…

Q: Worn armature bearings can result in higher than normal starter cranking current draw?

A: Moderate cranking and high current draw regularly demonstrate worn bearings or bushings inside…

Q: Transmission angle is the angle between and link of a four bar mechanism

A: