In a four bar mechanism the link AB rotates with angular velocity of 20rad/s and angular acceleration of 100 rad/s both in clockwise direction when it make an angle of 45° with link AD which is fixed .The length of various linkages are AB=CD=400 mm,BC3D500mm and AD=750mm .Neglect the gravitational effect and friction.The mass of link is 5kg/m. Find the torque on output link B. (3) E (2) (4) A (1)

In a four bar mechanism the link AB rotates with angular velocity of 20rad/s and angular acceleration of 100 rad/s both in clockwise direction when it make an angle of 45° with link AD which is fixed .The length of various linkages are AB=CD=400 mm,BC3D500mm and AD=750mm .Neglect the gravitational effect and friction.The mass of link is 5kg/m. Find the torque on output link B. (3) E (2) (4) A (1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A shaft is rotating at a uniform angular speed. Four masses M1, M2, and M3 and M4 of magnitudes 300kg, 450kg, 360kg, 390kg respectively are attached rigidly to the shaft. The masses are rotating in the same plane. The corresponding radii of rotation are 200mm, 150mm, 250mmand 300mm respectively. The angle made by these masses with horizontal are 0°.45°, 120°and 255°respectively. Find-(i) the magnitude of balancing mass (ii) the position of balancing mass if its radius of rotation is 200mm.
A single cylinder reciprocating engine has speeded 300 RPM. Stroke 250 mm, mass of reciprocating parts 50 kg. Mass of revolving parts at 150 mm radius 37 kg. If two fourth of the reciprocating parts and all the revolving parts are to be balanced, find (i) The balance mass required at 400 mm radius (ii) The residual unbalanced force when the crank has rotated 45° TDC.
1) Three small spheres are rigidly mounted to a horizontal shaft with rotates with angularvelocity omega as shown. Neglect sphere radii, ignore gravity. Spheres have masses m1, m2andm3 as shown.a. What is the angular momentum HO about O the center of the coordinates shown?b. At this instant, what is Ax , the x component of the bearing force at A to offset the dynamicimbalance? Note that you are NOT asked to find any other forces (Ay, Ox, or Oy) in interestof time.
The system shown below is made up of two pulleys attached to the same shaft, with radii ri and re of 0.29 mm and 0.43 mm, respectively. The total mass of the pulley system is 14 kg and its turning radius is 0.26 mm from its center. The mass of block A is 9 kg and the mass of block B is 2 kg. If the coefficient of kinetic friction between block B and the floor is 0.2, find the angular acceleration of the pulley.
A torque T = 0.30 N-m is applied to a bevel gear B. Bevel gear D meshes with gear B and drives pump A. Gear B has a radius of gyration of 150 mm and a weight of 50 N, whereas gear D and the im- peller of pump A have a combined radius of gy- ration of 50 mm and a weight of 100 N. Find how many revolutions of gear B are needed to get the pump up to 200 rpm from rest. What is the power output of the pump at this speed if it is 90% efficient.
A uniform rod of mass M = 2.3 kg and length L = 0.2 m, lying on a frictionless horizontal plane, is free to pivot about a vertical axis through one end, as shown. The moment of inertia of the rod about this axis is given by 1/3 ML2. If a force F = 7 N, q = 47° acts as shown, what is the resulting angular acceleration (in rad/s2) about the pivot point?
The slender, homogeneous rod shown in the figure below is 3 m in length and has a mass of 12 kg. At the instant shown, the rod has an angle to the horizontal of 60-degrees and an angular velocity of 2 rad/s clockwise. Both walls are smooth and provide negligible friction. At the instant shown, what are the reaction forces at A and B? What is the angular acceleration of the rod's center of mass?
The rope shown in the figure below is wound around a cylinder of mass 4.0 kg and I = 0.020 kg m2, about the cylinder axis. If the cylinder rolls without slipping, what is the linear acceleration of its center of mass? What is the frictional force? Use an axis along the cylinder axis for your computation. What happens if the frictional force between table and cylinder is negligible? Choose any axis for your computation.
A double slide mechanism is seen in the figure. AB rod with weight W = 95N and length L = 1.64 is guided in such a way that it can move freely from its ends. When θ = 70 °, with the horizontal force P acting on the slide B, the AB rod starts quietly in a clockwise direction with an angular acceleration α = 4.8 rad / s ^ 2. Calculate the acceleration of the center of gravity G of rod AB. Calculate the forces Ax, By and P.
An elongated rod of mass 4-kg has a mass of 2-kg at point A to a block moving vertically, 4-kg at point B pinned to a massive disk. The disc rotates without rolling, It is assumed that the block also moves in a frictionless channel. Please pay. The mechanism is released when stationary at θ=60º. Find the angular velocity of the rod when θ=0º.
Exactly one turn of a flexible rope with mass m is wrapped around a uniform cylinder with mass M and radius R. The cylinder rotates without friction about a horizontal axle along the cylinder axis. One end of the rope is attached to the cylinder. The cylinder starts with angular speed v0 . After one revolution of the cylinder the rope has unwrapped and, at this instant, hangs vertically down, tangent to the cylinder. Find the angular speed of the cylinder and the linear speed of the lower end of the rope at this time. Ignore the thickness of the rope.
The connecting rod of a horizontal reciprocating engine is 400 mm and length of the stroke is 200mm. The mass of the reciprocating parts is 125 kg and that the connecting rod is 100 kg. The radius of gyration of the connecting rod about an axis through the centre of gravity is 120 mm and the distance of centre of gravity of the connecting rod from big end centre is 160 mm. The engine runs at750 r.p.m. Determine graphically the torque exerted on the crankshaft when the crank has turned 30° from the inner dead centre.