In a microcontroller program, a subroutine starts at address 016F and ends with a 'return' instruction at address 0172. A call subroutine' instruction is located at address 02F3. Assuming that the microcontroller has one complete instruction in each address, list the changes in the contents of the program counter and stack between the time of execution of the instruction before the call and the instruction following the call. Indicate an unknown value as XXXX.

In a microcontroller program, a subroutine starts at address 016F and ends with a 'return' instruction at address 0172. A call subroutine' instruction is located at address 02F3. Assuming that the microcontroller has one complete instruction in each address, list the changes in the contents of the program counter and stack between the time of execution of the instruction before the call and the instruction following the call. Indicate an unknown value as XXXX.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

The processor has performed the following addition operation: 0x01A0+ 0xC410------0xC5B0 What decimal numbers did the processor add up, and what is the result of the addition if the programmer chose these numbers to be signed 16-bit number, where the lower four bits represent the fractional part of the number?
1. Study this program, then answer the questions that follow: MOV AL, 64H ADD AL, 27H DAA a) What does the accumulator contain immediately after the ADD instruction is executed? What do the CY and AC flags contain? b) What does the accumulator contain after the DAA instruction is executed? What do the CY and AC flags contain?
Show the program execution for the following program.The hypothetical machine has four (4) opcodes:1110 = LOAD0111 = STORE1000 = ADD
Part 1:Compile the assembly code for the following C code. Part 2: What is the process for calculating the total number of RISC-V instructions needed to execute the function? Can you find an exact solution? If so, what is that? If not, why not?
When programming in Boolean, what statement should be used to connect components in parallel?
Write the Boolean expression for each of the logic circuits in Figure?
1. What is the name of the wires that connect the memory with the registers? What is the name of the wires that connect the program control with the memory control?
In a multibyte addition program, when must you use the ADD instruction? When must you use the ADC instruction?
1.Show the status of PSW (Program status word) after addition of two 8bit numbers 26H and 3FH. Also draw status of flag register with help of diagram? 2. Mention the addressing mode, function and how many bytes instruction for the following instructions? ADI 42H b. LXI H, 2500H c. RLC 3. Write assembly language program to add to 8-bit numbers with carry. First numbers stored on memory location 2500h, second number on 2501H and store 8bit result on memory location 2502H and carry on 2503H.
In a simple copy machine, a stop signal, S, is to be generated to stop the machine operation and energize an indicator light whenever either of the following conditions exists: (1) there is no paper in the paper feeder tray; or (2) the two micro-switches in the paper path are activated, indicating a jam in the paper path. The presence of paper in the feeder tray is indicated by a HIGH at logic signal P. Each of the micro-switches produces a logic signal (Q and R) that goes HIGH whenever paper is passing over the switch to activate it. Design and build the logic circuit to produce a HIGH at output signal S for the stated conditions, and implement it using the two-input NAND chip.
In a simple copy machine, a stop signal, S, is to be generated to stop the machine operation and energize an indicator light whenever either of the following conditions exists: (1) there is no paper in the paper feeder tray; or (2) the two micro-switches in the paper path are activated, indicating a jam in the paper path. The presence of paper in the feeder tray is indicated by a HIGH at logic signal P. Each of the micro-switches produces a logic signal (Q and R) that goes HIGH whenever paper is passing over the switch to activate it. (3) Regardless the state of the previous two statements the stop signal is active if there is no internet connection to the machine or if the inside temperature sensor is active (This sensor is active if the inside temperature of the machine reaches a certain threshold temperature). Design and build the logic circuit to produce a HIGH at output signal S for the stated conditions.
Can you draw a logic diagram with gates for the equation in the photo, please?