In a parallel resistors DC circuit, having different resistors O a. the voltage across the resistors is different and current in each resistor is same O b. the voltage across the resistors is different and current in each resistor is different O c. the voltage across the resistors is same and current in each resistor is different O d. the voltage across the resistors is same and current in each resistor is same

In a parallel resistors DC circuit, having different resistors O a. the voltage across the resistors is different and current in each resistor is same O b. the voltage across the resistors is different and current in each resistor is different O c. the voltage across the resistors is same and current in each resistor is different O d. the voltage across the resistors is same and current in each resistor is same

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter9: Current And Resistance

Section: Chapter Questions

Problem 84CP: In this chapter, most examples and problems involved direct current (DC). DC circuits have the...

See similar textbooks

Similar questions

An electronic apparatus may have large capacitors at high voltage in the power supply section, presenting a shock hazard even when the apparatus is switched off. A “bleeder resistor" is therefore placed across such a capacitor, as shown schematically in Figure 21.50, to bleed the charge from it after the apparatus is off. Why must the bleeder resistance be much greater than the effective resistance of the rest of the circuit? How does this affect the time constant for discharging the capacitor?
In this chapter, most examples and problems involved direct current (DC). DC circuits have the current flowing in one direction, from positive to negative. When the current was changing, it was changed linearly from I=ImaxtoI=+Imax and the voltage changed linearly from V=Vmax to V=+Vmax where Vmax=ImaxR .Suppose a voltage source is placed in series with a resistor of R = 10 that supplied a current that alternated as a sine wave, for example, I(t)=(3.00A)sin(24.00st) . (a) What would a graph of the voltage drop across the resistor V(t) versus time look like? (b) What would a plot of V(t) versus I(t) for one period look like? (Hint: If you are not sure, try plotting V(t) versus I(t) using a spreadsheet.)
Consider the circuit shown in the preceding problem. Write equations for the power supplied by the voltage sources and the power dissipated by the resistors in terms
Two different electrical devices have the same power consumption, but one is meant to be operated on 12G-V AC and the other on 240-V AC. (a) What is the ratio of their resistances? (b) What is the ratio of their currents? (c) Assuming its resistance is unaffected, by what factor will the power increase if a 120-V AC device is connected to 240-V AC?
Check Your Understanding Circuit breakers in a home are rated in amperes, normally in a range from 10 amps to 30 amps, and are used to protect the residents from harm and their appliances from damage due to large currents. A single 15-amp circuit breaker may be used to protect several outlets in the living room, whereas a single 20-amp circuit breaker may be used to protect the refrigerator in the kitchen. What can you deduce from this about current used by the various appliances?
Integrated Concepts If you wish to take a picture of a bullet traveling at 500 m/s, then a very brief flash of light produced by an RC discharge through a flash tube can limit blurring. Assuming 1.00 mm of motion during one RC constant is acceptable, and given that the flash is driven by a 600F capacitor, what is the resistance in the flash tube?
Integrated Concepts Use the ECG in Figure 20.34 to determine the heart rate in beats per minute assuming a constant time between beats. Figure 20.34 A lead II ECG with corresponding arterial blood pressure. The QRS complex is created by the depolarization and contraction of the ventricles and is followed shortly by the maximum or systolic blood pressure. See text for further description.
A student in a physics lab mistakenly wired a light bulb, battery, and switch as shown in Figure 21.44. Explain why the bulb is on when the switch is open, and off when the switch is closed. (Do not try this-it is hard on the battery!)
In view of the small currents that cause shock hazards and the larger currents that circuit breakers and fuses interrupt, how do they play a role in preventing shock hazards?
Common household appliances are rated at 110 V, but power companies deliver voltage in the kilovolt range and then step the voltage down using transformers to 110 V to be used in homes. You will learn in later chapters that transformers consist of many turns of wire, which warm up as current flows through them, wasting some of the energy that is given off as heat. This sounds inefficient. Why do the power companies transport electric power using this method?
When making an ECG measurement, it is important to measure voltage variations over small time intervals. The time is limited by the RC constant of the circuit-it is not possible to measure time variations shorter than RC. How would you manipulate R and C in the circuit to allow the necessary measurements?
Find the current through a person and identify the likely effect on her if she touches a 120-V AC source: (a) if she is standing on a rubber mat and offers a total resistance of 300 k; (b) if she is standing barefoot on wet grass and has a resistance of only 4000 k .