Quest Air (at atmospheric pressure) at a day bulb temp.anof 40°c and wet bulb temp. of 20°℃ is humidifiedinair washer operating with continuouswater recirculation. The wet bulb depressionthe exif is 25% of that at theindetThe day bulb temperature at the exitof the air washer is ?at

Given data; Air at atmospheric pressure; Wet bulb temperature, WBT=200C Dry bulb temperature,…

Answered: The day bulb temperature at the exit

Engineering

Mechanical Engineering

The day bulb temperature at the exit

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: What is the relation between modulus of elasticity and modulus of rigidity.

A: Modulus of Elasticity:- The slope of stress-strain curve under direct loading is called Modulus of…

Q: For the truss loaded as shown, determine the equation for the line of action of the stand-alone…

A: Given data: F1=20 kNF2=20 kNF3=10 kNF4=50 kNM=145 kN.m Need to determine the equation of line of…

Q: Product of mass and velocity called linear momentum T O F O

Q: Can you calculate the work done if .the forces are non conservative

A: 1) A conservative force is one for which the work done is independent of path. 2) A force is…

Q: If the resultant of the loads shown passes through point B, determine the equivalent force-couple…

Q: P₁ = 10 MPa •T₁ = 600 °C 2 21 A. For the turbine, for mass flow rate of 3,000 kg/hr, calculate: 1.…

Q: The L-shape frame shown in Figure 2 is fixed and supported at point A and experienced multiple…

Q: * Fixed-Fixed bar was 20 centigrade degree at room temperature, Determine the thermal stress when…

A: Given data as per the question The initial temperature of the bar = 200 c The final temperature of…

Q: 4. The surface of the Sun has a temperature of about 6000 K. At what wavelength does the Sun emit…

A: when a wave form signal from any source propagte in the space or through the wire, then the distance…

Q: Two plates are a length (L) and thickness (t). were welded together. Assume these plates have…

A: When two plates of same length and thickness are joined together using welding, the lap joint would…

Q: B=56 inside diameter = 66 in. wall thickness=0.23 in. allowable normal stress perpendicular to the…

Q: A printed circuit board with constant surface temperature dissipates 100 W from one side over an…

A: Introduction: The change in temperature is connected with heat transmission. The heat transmission…

Q: are 3 methods that can be used to control the metal flow under the blank holder in deep drawing…

A: Drawing is a metalworking technique that involves stretching metal, glass, or plastic by applying…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 2000 mm² and an…

A: Answer: The maximum load that can be supported by the structure without exceeding either allowable…

Q: Calculate the Net Positive Suction Head (NPSH) for a pump handling 100,000 kg/hr flow of water…

Q: The 480-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

Q: C- A rigid 1 m³ tank contains nitrogen gas, initially at 10 bar, 27 °C. Heat transfer to the gas…

A: Write the given data. V1=1 m3P1=10 bar=P2T1=27 °C=27+273=300 KT2=400 K

Q: Four people are attempting to move a stage platform across the floor. If they exert the horizontal…

Q: What’s the formula for finding center of gravity when thickness is included

A: center of gravity is a point where we considered that the weight of a body is acting. In uniform…

Q: Determine the force in each member of the loaded truss as a result of the hanging weight W = 205 lb.…

Q: 1. Find the precision value of X1 and X2? X₁ = 101 X₁ =98 X₂ = 98.5

A: Given data: Xn = 101X1 = 98X2 = 98.5 We have to find the precision value of X1 and X2

Q: Determine the speed v which the 525-kg four-man bobsled must have in order to negotiate the turn…

Q: A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three…

Q: Given the FLEXURAL RIGIDITY=6000 :KN.m^2. The deflection value at point A is 50 kN A 9m B

Q: Can you calculate the work done .the forces are non conservativ Yes No

A: Work for a nonconservative force is contingent on the path pursued. Friction is a nonconservative…

Q: A cylinder is to be tested by Engr. Dejesa using two working fluids. The working fluids are oxygen…

Q: The simply supported beam as shown in Figure 1 has the rectangular cross-section (b = 85 mm, h = 105…

Q: The combined action of the three forces on the base at O may be obtained by establishing their…

Q: In rectilinear motion of a particle, the work is equal to the change in the .kinetic energy of the…

A: Work energy principle for rectilinear motion, For particle if it performs rectilinear motion under…

Q: Two air streams at standard atmosphere are mixed adiabatically with the first air stream at 15°C db,…

Q: .) How many different types of welds are specified on the print and what are they? (Hint: look at…

A: Welds come in a variety of shapes, which are best defined by their cross-sectional form. The fillet…

Q: (9) Find the angle between two vectors: A=31+4j-5k, (1) Scalar product. (2) vector product. B =…

Q: Please can you explain how the concepts of the kinematics of rigid bodies are related to position,…

A: Introduction: A rigid body is a perfect representation of a body that does not deform or alter its…

Q: Moist air initially at standard atmospheric pressure, 15°C db, 70% relative humidity undergoes a…

A: Note: As per the policy, we can solve the first question from multiple questions. Please resubmit…

Q: Air initially at 101.325 kPa, 30°C db and 40% relative humidity undergoes an adiabatic saturation…

Q: With the assumption of no slipping, determine the mass m of the block which must be placed on the…

Q: pective Gears Q and Rare mounted on the same shaft as shown in the figure below. The diameter of the…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 7 mm2.…

Q: Determine the maximum load P that can be safely carried by the titanium bar. The factor of safety is…

A: Given f=2 allowable stress of titanium =240MPa

Q: what should be its diameter? Also find the length of the middle portion, if the total extension of…

Q: B-A Refrigerant 134a is contained ank of volume 0.2 m³. Initially the refrigerant exists in a…

A: Given Data The volume of the tank is: V=0.2 m3 The initial temperature of the refrigerant is:…

Q: What is the specific heat of metal if its mass is 27 g and it requires 420 J of heat energy to…

A: Dear student, as per the given data, there is no correct option. Please find the attached solution.…

Q: An object of mass 1000 kg, initially having a velocity of 20 m/s, accelerates to a final velocity of…

Q: forming temperature condition. 8) In blanking operation, if the final blank diameter is 200 mm & the…

Q: Find the value of Maximum shear stress in rectangular section Shear force-40 N Area of section=2 mm2

A: Given data : Shear force V=40 N Section=Rectangular Area of section A=2 mm2

Q: B. For the cycle, calculate: 4. Network, W in KW 5. Cycle thermal efficiency, e.

A: For the Rankine cycle, Turbine inlet conditions are P1 = 10 MPa, T1 = 600 oC Condenser pressure =…

Q: * For the cross section shown in the figure. :Find the value of Y 40 mm A1 250 mm

A: Given

Q: SHL P Type here to search <-CFD-Hue Pape cice E Ⓒ1038 Question 11 S ACal Can X A Which of the…

Q: Find the value of Maximum shear stress in rectangular section Shear force-40 N Area of section=2 mm2

Q: 40 mm 220 mm For the cross section shown in the figure. Given the value of Y= 172 mm. Find the…

Concept explainers

Properties of Pure Substances

A substance with fixed chemical composition throughout is called a pure substance like water, air, and nitrogen. A pure substance does not have to be a single element or compound. A mixture of two or more phases of a pure substance is also a pure substance as long as the chemical composition is the same for all phases. These substances mainly have a constant/ uniform composition. The substances also have fixed boiling and melting points. A pure substance takes part in a chemical reaction to form predictable products.

Question

Quest Air (at atmospheric pressure) at a day bulb temp.
an
of 40°c and wet bulb temp. of 20°℃ is humidified
in
air washer operating with continuous
water recirculation. The wet bulb depression
the exif is 25% of that at theindet
The day bulb temperature at the exit
of the air washer is ?
at

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the temperature entering the cooling sectionwhen 25 kW of heat are removed and the air exits at 15 deg C, a relative humidity of 30% and a volumetric flowrate of 0.7 m^3/s?
Example 9. Moist air at 20°C dry-bulb and 8°C thermodynamic wet-bulb temperature is to be processed to a final dew-point temperature of 13°C by adiabatic injection of saturated steam at 110°C. The rate of dry airflow is 2 kg/s. Find the final dry-bulb temperature of the moist air and the rate of steam flow.
A winter air-conditioning system adds for humidification 0.0025kg/s of saturated steam at 101 kPa pressure to an airflow of 0.36 kg/s.The air is initially at a temperature of 6.2019123751 C DB with a relativehumidity of 20 percent. What are the dry-bulb and wet-bulb temperaturesof the air leaving the humidifier?Kindly graph it on the given image
Which is better for humidifying air, adding steam or water? Justify?
A winter air-conditioning system adds for humidification 0.0025 kg/s of saturated steam at 100 kPa pressure to an airflow of 0.36 kg/s. The air is initially at a temperature of 15°C with a relative humidity of 20 percent. The barometric pressure is 90 kPaa. What is the dry temperature of the air leaving the humidifier °C?
Moist air at 20°C dry-bulb and 8°C thermodynamic wet-bulb temperature is to be processed to a final dew-point temperature of 13°C by adiabatic injection of saturated steam at 110°C. The rate of dry airflow is 2 kg/s. Find the final dry-bulb temperature of the moist air and the rate of steam flow.
An ammonia compressor has a volumetric effienciy og 85%, operating condensing & evaporating temperatures of 40 C & 10 C respectively for a cooling capacity of 10 tons with compression index of 1.2, mean piston speed of 2m/s, 5% clearance & bore to stroke ratio of 0.7. Determine the ff: 4. work of compressor in kj/kg 5. power of compressor in kj/kg 6. cooling coefficient of performance
Air enters a humidifier at 34.25°C and 30% RH. If the air leaves the humidifier at 70% RH. Determine: The exit dry-bulb temperature of the air in °C.The saturation effectiveness in %.
Compute for the (a) dryness factor, (b) internal energy, (c) enthalpy, and (d) entropy of a saturated water at21.225 MPa.
Air at a dry ball temperature of 90 danC and 4% RH is passed over the cooling coil so that the air dry bulb temperature becomes 45˚C. how much heat is released from the air in the process? = (Kj / kg)
Determine the power required for a forced draught and induced draught fan in a boiler having coalconsumption of 25 kg/min and air/fuel ratio of 19 by mass. The ambient air temperature and hotgas temperature at exit are 30C and 140C respectively. Draught required is equivalent to 32.2 mmof water and mechanical efficiency of motor/fan is merely 70%
Show that ? and ? for superheated steam depend strongly on temperature and relatively slightly on pressure.