In an Axial Compression member, if the compression stress in the concrete is > 0.51, and the compression stress in the steel (< (t), Hooke's Law can be applied for the axial compression member Select one O True O False

In an Axial Compression member, if the compression stress in the concrete is > 0.51, and the compression stress in the steel (< (t), Hooke's Law can be applied for the axial compression member Select one O True O False

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cast iron tube 3m long is completely filled with concrete and used as a vertical strut. if the external diameter of the tube is 40mm and the wall is 35mm thick, determine the maximum compressive load, the composite strut can support if the stress in the concrete is not to exceed 2N/mm^2. By how much should the strut shorten under the load. For cast iron Ea=100 GN/m^2 and for concrete , Eb=10 GN/m^2
A prismatic bar with a length L = 3 ft andcross-sectional area A = 8 in2 is compressed by anaxial centroidal load P =10 kips. Determine thecomplete state of stress acting on an inclined sectionpq that is cut through the bar at an angle θ = 35°, andshow the stresses on a properly oriented stress element.
Calculate the resulting stress in an aluminum wire, 4-m long and 2.6 mm in diameter, if a 12.5 -kg fixture is hung from the wire? Young's modulus for aluminum is 7.0 × 10^10 N/m^2. Express the answer in Pa and as a whole number.
A steam boiler is to have a 300 mm diameter hand placed hole on one end. If themaximum internal pressure is 1.3 MPa, how many 15 mm holes will be required to keepthe cover plate in position? The root diameter of a 15 mm bolt is 12 mm. The allowabletensile stress in the bolts is 100 MPa and the initial stress in the bolts when they aretightened is 600 MPa.
A steel rod of 30 mm diameter is enclosed centrally in a hollow copper tube of external diameter 40 mm and 5 mm thick. The composite bar is then subjected to an axial pull of 45 kN. If the length of the compound rod is 150 mm , and the elasticity moduli are Est = 200 GPa and Ecu = 100 GPa , determine: 1.2.1 The stresses in the rod and tube
A two-story building has steel columns ABin the first floor and BC in the second floor, as shownin the figure. The roof load P1 equals 400 kN, and thesecond-floor load P2 equals 720 kN. Each column hasa length L = 3.75 m. The cross-sectional areas of thefirst- and second-floor columns are 11,000 mm2 and3900 mm2, respectively.(a) Assuming that E = 206 GPa, determine thetotal shortening δAC of the two columns due tothe combined action of the loads P1 and P2.(b) How much additional load P0 can be placedat the top of the column (point C ) if the totalshortening δAC is not to exceed 4.0 mm?
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P = 35000 lb and the stress in the steel, aluminum, and bronze sections are limited to 20 ksi, 28 ksi, and 18 ksi, respectively, determine the safest area considering the maximum stress in the aluminum.
b.The strong room of a school where an exam question papers are kept is made up ofrectangular metal bars.One bar has a width of 10 mmand would beable to withstand a maximum compressive stress of 20 MPa. i.Prove that,the minimum breadth of thisbar can withstand a burdened with a force of 3 KN. ii.If the bar in question is 2 mlong and decreases in length by 0.25 mmwhen aforce isapplied, then show thata percentage strain can be obtained. iii.What would be its Modulus of Elasticity, E?
Consisting of chrome-nickel and bronze,the largest horizontal P force it can carry, and chromium-nickelCalculate the length change that will occur in the cable.Cross Section Areas: A chrome-nickel = 3 cm2A bronze = 6 cm2Elasticity modules: E chrome-nickel = 215 Gpa, E bronze = 90 GpaSafety Stresses: (σem) bronze = 100 Mpa, (σem) chromium-nickel = 600 Mpa
A closed cylindrical vessel made of steel plate 10 mm thick, with a plain ends carries fluid under a pressure of 20 N/mm², The diameter of cylinder is 400 mm and the length is 1500 mm. The steel plate young's modulus is 180000 N/mm² with a poisons ratio of .3 ,Determine the following a) The hoop stress in the cylinder wall b) The diameter change c) The change in Length
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.
a) A cylinder with a 0.30-m inner diameter and a 0.40-mouter diameter is internally pressurized to 100 MPa. Determinethe maximum shear stress at the outer surfaceof the cylinder. b) A thin-walled cylinder containing pressurized gas isfixed by its two ends between rigid walls. Obtain anexpression for the wall reactions in terms of cylinderlength l, thickness th, radius r, and internal pressure pi.