In clock mechanism, reverted gear train is used. Select one: O True O False There are six gears A, B, C, D, E, F in a compound gear train. The numbers of teeth in the gears are 20, 60, 30, 80, 25 and 75 respectively. The ratio of speeds of the driven gear F to the driver A is O 4/15 O 8/15 O 1/24 O 1/8

In clock mechanism, reverted gear train is used. Select one: O True O False There are six gears A, B, C, D, E, F in a compound gear train. The numbers of teeth in the gears are 20, 60, 30, 80, 25 and 75 respectively. The ratio of speeds of the driven gear F to the driver A is O 4/15 O 8/15 O 1/24 O 1/8

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter38: Manual Transmissions And Transaxles

Section: Chapter Questions

Problem 5ASRQ: Technician A says that if a single idler gear is used to obtain reverse gear, its size and number of...

See similar textbooks

Similar questions

Technician A says that if a single idler gear is used to obtain reverse gear, its size and number of teeth must be used to calculate gear ratios. Technician B says that an idler gear is often used for reverse gear because it causes the output shaft to rotate in the reverse direction of the input shaft. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
A system of 5 gears (gear A, B, C, D, E) with the number of teeth 20, 25, 35, 26 and 34, respectively. Gear A has a rotational speed of 600 rpm counterclockwise. a) Determine the direction and magnitude of the rotational speed for each gear (gear B, C, D, E) b) Determine the transmission number (speed ratio)
A gear box conta8he 3 sizes of gears, 8 tooth, 32 tooth and 64 teeth. What is the gear ratio when the 8 tooth gear drives the 64 tooth gear?
The teeth of the gear arrangement have Gear A=40teeth, Gear B=70 teeth and Gear C= 50teeth, a pinion (driver Gear) that rotates at 625 rpm, and idler Gear B and a driven gear (Gear C). The gears have a module of 5mm and a pressure angle of 200. Find the pitch diameter of gear C in mm.
7. The following data relate to a pair of 20° involute gears in mesh : Module = 6 mm, Number of teeth on pinion = 17, Number of teeth on gear = 49; Addenda on pinion and gear wheel = 1 module. Find : (a) The number of pairs of teeth in contact (b) The angle turned through by the pinion and the gear wheel when one pair of teeth is in contact (c) The ratio of sliding to rolling motion when the tip of a tooth on the larger wheel (i) is just making contact (ii) is just leaving contact with its mating tooth (iii) is at the pitch point.
An epicyclic gear train has 3 shafts A,B and CA is an input shaft running at 100 rpm clockwise. B is an output shaft running at 250 rpm clockwise. Torque on A is 50 kNm (clockwise). C is a fixed shaft. The torque to fix C
The following data relate to two meshing gears: Velocity ratio =1:3;Module: 4mm; Pressure Angle: 20°; Center distance: 200 mm Determine the number of teeth and the base circle radius of the gear wheel.
For the gear train below, th numbers of teeth for individual gears are 12 9gear #1), Gear 18 (gear #2), 14 (gear #3), and 18(gear #4), To obtain a counter-clockwise rotation of 1500 rpm for the output gear(#4). What should be the rotation speed of the input gear (#1) and in which directions should the input gear rotate
Q#2: For the two-gear system shown in following figure; a) Calculate Gear Ratio b) If the speed of Driver Gear is 30 revolutions per minute (rpm) then what will be speed of Driven Gear? c) Among two gears (driven gear and driver gear), which gear has highest speed in revolutions per minute.? d) What should be number of teeth on Driven gear to move with speed of 4 times than that of Driver Gear?
Q#2: For the two-gear system shown in following figure; a) Calculate Gear Ratio b) If the speed of Driver Gear is 30 revolutions per minute (rpm) then what will be speed of Driven Gear? c) Among two gears (driven gear and driver gear), which gear has highest speed in revolutions per minute.? d) What should be number of teeth on Driven gear to move with speed of 4 times than that of Driver Gear? (Hint: If your ID is 114-2020, then compression force would be 114 N)
2. Determine the required torque for each gear. Identify which gear has the maximum required torque. Gear 1 2 3 4 5 RPM 100 400 1200 3600 7200 Torque output (Nm) 30
Write a gear ratio equation between 2 gears for number of teeth, torque, angular velocity, aswell diameter. You have 2 straight gears 1 and 2 in mesh