Figure shown below illustrates the gears in a speed-change gearbox used in machine tool applications. By sliding the cluster gears on shafts Band C, nine speed changes can be obtained as shown in Table given below. The problem of the machine tool designer is to select tooth numbers for the various gears (2 to 10) so as to produce a reasonable distribution of speeds for the output shaft. The gears 2, 6 and 9 are having 20, 25 and 50 teeth respectively. The input shaft speed is 450 rpm and the output speed can vary from 137 rpm to 580 rpm depending on the sequence of the gears. If the output speed obtained through the gear sequence 2-5-5-8 is 257 rpm and if the minimum and maximum number of teeth in the gear system are 20 and 50 respectively, (i) Suitable tooth numbers for the remaining gears (3,4,5,7,8 & 10)

Figure shown below illustrates the gears in a speed-change gearbox used in machine tool applications. By sliding the cluster gears on shafts Band C, nine speed changes can be obtained as shown in Table given below. The problem of the machine tool designer is to select tooth numbers for the various gears (2 to 10) so as to produce a reasonable distribution of speeds for the output shaft. The gears 2, 6 and 9 are having 20, 25 and 50 teeth respectively. The input shaft speed is 450 rpm and the output speed can vary from 137 rpm to 580 rpm depending on the sequence of the gears. If the output speed obtained through the gear sequence 2-5-5-8 is 257 rpm and if the minimum and maximum number of teeth in the gear system are 20 and 50 respectively, (i) Suitable tooth numbers for the remaining gears (3,4,5,7,8 & 10)

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter34: Emission Control Diagnosis And Service

Section: Chapter Questions

Problem 2RQ: What will result from too little EGR flow? And what can cause a reduction in the flow?

See similar textbooks

Similar questions

It is required to feed an industrial ventilation system at a rate of Q = 23,000 ft3/min that demands a pressure increase of DP = 350 Pa under normal atmosphere conditions (Patm = 101 kPa and T=20ºC). Estimate the power demand assuming a rotor efficiency of 75%.
Provide clear and complete solution as well as diagram. The initial condition of air in an air compressor is 97 kPa and 27 oC and discharges air at 350 kPa. The bore and stroke are 250 mm and 280 mm, respectively with percent clearance of 6 percent running at 310 rpm. Find the volume of air at suction in m3/hr. A. 232.61 C. 156.34B. 289.16 D. 135.23
The initial condition of air in an air compressor is 98kpa and 27C and discharges at 500kpa. The bore and stroke are 360mm and 390mm, respectively with percent clearance of 7% running at 300rpm. Find the mass flow of air in kg/s at suction. ANS. 0.19108
A reservoir supplies water through 100 m of 30-cm-diameter cast iron pipe to a turbine that extracts 80 hp from the flow. Given that Δz = 30 m. The water then exhausts to the atmosphere. Neglect minor losses. For water at 20°C, take ρ = 998 kg/m3 and μ = 0.001 kg/m-s. Take π = 22/7. In determining the flow rate of the given flow, two solutions are obtained. Are both the solutions valid? Yes or no?
[1] A Pelton turbine is driven by two jets, generating 5.0 MW at 80 rev/min. The effective head at the nozzles is 300 m of water and the nozzle velocity coefficient, KN = 0.97. The axes of the jets are tangent to a circle 2 m in diameter. The relative velocity of the flow across the buckets is decreased by 17% and the water is deflected through an angle of 165 deg. Neglecting bearing and windage losses, determine: (i) the runner efficiency; (ii) the diameter of each jet; (iii) the power specific speed.
A turbine of 9000 B.H.P. is working under a head of 25 mand runs at 100 R.P.M.- What will be the type of turbine ? Whatshould be its speed and power, when it is working under a head of16 m?
A Kaplan turbine has the following specifications: H =25 ft., N=400 rpm; power = 650 hp. If the efficiency of the unit is 90%, estimate (a) the flow rate, (b) approxi-mate diameter of the runner, (c) turbine setting to avoid cavitation if the location is at sea level, and (d) turbine setting to avoid cavitation if the location of the unitis at an elevation of 5000 ft. The local temperature is 60°F.Ans: (a) Q=254 cfs; (c) Hs=5.8 ft.; (d) 0.12 ft.
For a single acting reciprocating pump, piston diameter is 150 mm, stroke length is 300 mm, and rotational speed is 50 r.p.m. The pump is required to lift water to a height of 18 m. Determine the theoretical discharge. If the actual discharge is 4.0 lit./sec, and the mechanical efficiency is 80% determine the volumetric efficiency, slip, theoretical power and the actual power required.
Suppose the pump of Fig. P14–23 is operating atfree delivery conditions. The pipe, both upstream and downstreamof the pump, has an inner diameter of 2.0 cm andnearly zero roughness. The minor loss coefficient associatedwith the sharp inlet is 0.50, each valve has a minor loss coefficientof 2.4, and each of the three elbows has a minor losscoefficient of 0.90. The contraction at the exit reduces thediameter by a factor of 0.60 (60% of the pipe diameter), andthe minor loss coefficient of the contraction is 0.15. Note thatthis minor loss coefficient is based on the average exit velocity,not the average velocity through the pipe itself. The total length of pipe is 6.7 m, and the elevation difference is (z1 - z2)= 4.6 m. Estimate the volume flow rate through this pipingsystem. Complete Answer, Thank you
The swept volume of the reversible diesel engine is 0.198 m^3/s and the mean effective pressure is 10 bar. Determine the break power of the engine if mexhanical effucuency if the engune is 70 %.
A Kaplan turbine working under a head of 81 5 m is dis-charging 295 m%/sec. of water at 75 R.P.M. and developing 38,000B.H.P.The runner dia is 7 m and boss diameter is 3 m.Determine (2) the inlet and outlet blade angles of runner, (i)mechanical efficiency and (in) overall efficiency.Assume hydraulic efficiency as 94%
[5] A Francis turbine operates at its maximum efficiency point at h0 = 0.94, corresponding to a power specific speed of 0.9 rad. The effective head across the turbine is 160 m and the speed required for electrical generation is 750 rev/min. The runner tip speed is 0.7 times the spouting velocity, the absolute flow angle at runner entry is 70 deg from the radial direction and the absolute flow at runner exit is without swirl. Assuming there are no losses in the guide vanes and the mechanical efficiency is 100%, determine (i) the turbine power and the volume flow rate; (ii) the runner diameter; (iii) the magnitude of the tangential component of the absolute velocity at runner inlet; (iv) the axial length of the runner vanes at inlet.