In one of the Rankine cycles, steam is expanded isentropically to an intermediate pressure in the high-pressure turbine and sent back to the boiler where it is reheated at constant pressure, usually the inlet temperature of the first turbine stage. Then, the steam expands isentropically in the second stage in the low-pressure turbine to the condenser pressure. Which type of Rankine cycle applies this process? Blank 1

In one of the Rankine cycles, steam is expanded isentropically to an intermediate pressure in the high-pressure turbine and sent back to the boiler where it is reheated at constant pressure, usually the inlet temperature of the first turbine stage. Then, the steam expands isentropically in the second stage in the low-pressure turbine to the condenser pressure. Which type of Rankine cycle applies this process? Blank 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What are the two benefits of adding a reheater to a Rankine cycle?
What are the four major accessories of a Rankine Cycle? Define each.
No 1 A Rankine cycle using superheat and reheat applications. Steam enters the stage 1 turbine at 8 MPa and a temperature of 480°C and expands at a pressure of 0.7 MPa. The steam is then reheated to a temperature of 440°C before entering the stage 2 turbine, where the steam expands in the condenser at a pressure of 0.008 MPa. The net power generated is 100 MW. No2 Using the data in number 1 above plus other data, namely each turbine has the same isentrapic efficiency of 85%, calculate the thermal efficiency of the cycle P.s Answer the number 2, number 1 just reference to answer number 2,thx
Give number sequence please. Problem 8: Steam in a reheat Rankine cycle enters the first-stage turbine at 8 MPa and 450°C. The steam leaves this first turbine at 800 kPa as a saturated vapor. The steam is then reheated isobarically back to 450°C before entering the second-stage turbine. At the exit of this second turbine, the steam is at 10 kPa and 50°C. The net power output of this cycle is 20 MW, and the water leaves the condenser as a saturated liquid. You may assume the pump functions isentropically and that there are no pressure losses in the condenser and boiler. Determine a. Draw this cycle on a T-s diagram. b. Calculate the isentropic efficiencies of the first- and second-stage turbines. c. Calculate the thermal efficiency of the cycle. d. Calculate the mass flow rate of steam, in kg/h. e. Calculate the rate of heat transfer from the water as it passes through the condenser, in MW.
The mass flow rate of steam is 5 kg/s for a Rankine Cycle. For the actual cycle, the turbine efficiency is 86%, turbine brake efficiency is 80%, and generator efficiency=90%. The inlet conditions of the turbine are 3MPa and 400⁰C while the condensing pressure is 50kPa. a. Sketch the P-v, T-s and h-s diagram of the Cycle b. Calculate for the ideal and actual steam rates and heat rates of the Rankine Cycle and Rankine Engine, respectively. c. Determine the energy chargeable and combine thermal efficiencies for the Rankine Cycle and Rankine engine, respectively
Steam enters the turbine of a power plant operating on the Rankine cycle (Fig. 2) at 873.15 Kand exhausts at 30 kPa. To show the effect of boiler pressure on the performance of the cycle,calculate the thermal efficiency of the cycle and the quality of the exhaust steam from theturbine for boiler pressures of 5000,7500, and 10 000 kPa. #Chemical Engineering #Chemical #Thermodynamics
Superheated steam generated in a power plant at a pressure of 8,600 kPa anda temperature of 500 ℃ is fed to a turbine. Exhaust from the turbine enters acondenser at 15 kPa, where it is condensed to saturated liquid, which is thenpumped to the boiler.(a) What is the thermal efficiency of a Rankine cycle operating at theseconditions?(b) What is the thermal efficiency of a practical cycle operating at theseconditions if the turbine efficiency and pump efficiency are both 75%?Which of the two efficiencies has greater impact on the thermal efficiency?(c) Sketch both cycles in the same T-s diagram.(d)If the power output of the turbine is 80,000 kW in case (b), calculate themass flow rate of the working fluid.(e) Calculate the heat transfer rates in the boiler and the condenser. Doublecheck the result for the condenser.(f) For both cases (a) and (b), make a comment about the operation of turbine(issue of cavitation). [one sentence is fine](g) How you would operate the condenser of a practical…
A powerplant generates steam at a pressure of 8500 kPa and a temperature of 773 K, which is fed into a turbine. Exhaust from the turbine now enters the condenser at a pressure of 10 kPa, where it is condensed to saturated liquid, then pumped to the boiler. Determine now the, (a) thermal efficiency of a Rankine cycle at these conditions?(b) thermal efficiency of a practical cycle at these conditions if the turbine and pump efficiency are both 0.60?(c) If the rating of the power cycle of part (b) is 80 000 kW, what is the steam rate and what are the heat transfer rates in the boiler and condenser?
15. The actual Rankine cycle has an 90.22% turbine isentropic efficiency and 81.14% pump isentropic efficiency. If in the ideal Rankine cycle, the heat input in the boiler - 903 kW, the turbine work output 394 kW, and pump work input = 17 kW, what is the actual cycle thermal efficiency if the heat input in the boiler is the same for the actual cycle? Express your answer in percent.
Construct the ideal Rankine cycle with three stages of reheating on a T-s diagram. Assume the turbine inlet temperature is the same for all stages. Justify how does the cycle efficiency vary with the number of reheat stages.
1. A reheat steam cycle has 13,580 kPa of throttle pressure at the turbine inlet and a 37.50308414 atm reheat pressure, the throttle and reheat temperature of the steam is 1302 R, condenser pressure is 4.3 kPa. Determine the difference between the simple Rankine cycle efficiency and the reheat Rankine cycle efficiency, in percent.
Steam enters the high-pressure turbine of an ideal reheat Rankine cycle at 10 MPa and 500°C. The low-pressure turbine inlet admits steam at 1 Mpa. Assume that the pump inlet is a saturated liquid at 10 kPa and that 80 MW of power is produced overall. 1. Report the overall thermal efficiency of the cycle as a percentage (number between 0 and 100) to one decimal place using rounding. 2. Report the mass flow rate, in kg/s, to one decimal place using rounding.