In the circuit of Figure 1.c, the voltage source is equal to V = 5 V and the load resistor is equal to R 200 N. Calculate the diode current, I, %3D Using the diode equation (precise method), assuming that the diode has a reverse saturation current of 0.1 pA at room temperature (300 K) and ideality factor of 1.2. Show all your calculation steps. i) Assuming that the diode has a constant forward voltage of 0.7 V.

In the circuit of Figure 1.c, the voltage source is equal to V = 5 V and the load resistor is equal to R 200 N. Calculate the diode current, I, %3D Using the diode equation (precise method), assuming that the diode has a reverse saturation current of 0.1 pA at room temperature (300 K) and ideality factor of 1.2. Show all your calculation steps. i) Assuming that the diode has a constant forward voltage of 0.7 V.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is CEMF?
Question For the following circuit, consider that both diodes ?1 and ?2 are ideal, that is ?? = 0 V. Consider the input source ??? = 48sen (??) V, a frequency of 60 Hz. Consider that the ??? of both diodes is high enough (negative value), so that both diodes never conduct in reverse. Carefully analyze the circuit to obtain: a) Sketch the curves of ??? and ????. b) The mathematical function of ???? in terms of ???.
Load resistor RL as shown is 12 kΩ. What are the nominal and worst-case values of Zener diode current and power dissipation if the power supply voltage, Zener breakdown voltage and resistors all have 5 percent tolerances?
a. Using standard resistor values, what value of R1 is needed to achieve 1.18V ±0.01V at Vout? b. Using the R1 value chosen in (a) part, what happens to the voltage Vout when a load resistance of 10K is added (between Vout and ground). c. What is the minimum value of load resistance required for correct operation Zener diode is used in place of si diode. Or you can assume zener current according to requirement Answer it i will rate
Explain dc diode resistance and ac diode resistance in terms of definitions, formula, and analysis. Discuss the given terms: Avalance voltage; Zener breakdown voltage; Reverse saturation current Explain the diode characteristic curve given:
diode zener a, DESIGN THE NETWORK IN THE FIGURE, TO KEEP, "VL" at 12 V for a variation in load (IL) from 0 to 200 mA, DETERMINE "Rs" and "Vz" b. determine "P2min" for the Zener diode from section a
solve all on the keyboard or will dislike if need draw on paper no problem (a) Explain the following terms as they relate to semiconductor diodes: Avalanche effect, Depletion region, and Intrinsic semiconductor (b) With the aid of fully labeled Crystal Lattice Structure diagram (s), explain how P-type material of a semiconductor is formed. (c) Draw a diagram showing the volt-ampere characteristic of a Zener diode. Explain the difference between Zener breakdown and Avalanche breakdown mechanisms. (d) A bridge rectifier is supplied with 120Vrms sinusoidal signal. If each diode has a junction voltage of 0.7V, determine: The peak voltage at the output of the rectifier and A suitable peak inverse voltage rating of each diode
Plot the diode forward characteristics from the results obtained, and determine the cut in voltage Vγ from the sketch. From the sketched characteristic curve determine the static resistance of the diode ???
How is Zener diode connected into a circuit? What determines the voltage at which a Zener diode break down? What considerations go into determining the power dissipation rating of a Zener diode? Draw a label the schematic symbol used to represent a Zener diode What determines the maximum Zener current of a Zener diode? What is the difference between the maximum Zener current and the reverse current for a Zener diode? What does a positive Zener voltage temperature coefficient signify? What does a negative Zener voltage temperature coefficient signify? How can a Zener diode be temperature compensated?
1. Plot the diode forward characteristics from the results obtained, and determine the cut in voltage Vγ from the sketch
Kindly explain it to me this question below. No need to illustrate just explain directly. Draw the equivalent circuit and characteristic curve of a forward biased diode using the second or practical device model. When is this model commonly used?
The full-wave rectiﬁer ias shown is operating at a frequency of 60 Hz, and the rms value of the transformer output voltage is 18 V. (a) What is the value of the dc output voltage if the diode voltage drop is 1 V? (b) What is the minimum value of C required to maintain the ripple voltage to less than 0.25 V if R = 0.5 Ω? (c) What is the PIV rating of the diode in this circuit? (d) What is the surge current when power is ﬁrst applied? (e) What is the amplitude of the repetitive current in the diode?