The full-wave rectifier circuit shown in Figure Q1(d) has a center-tapped transformer. The load resistance, R is 100 2 and the output, V. waveform is given in Figure Q1(d). Assume practical silicon diode model. D ; 2 ): 1 R P. 5V OV Figure QI(d) (i) Calculate the DC load voltage, DC load current, and PIV of each diode. Find the peak input voltage, Vi and then sketch the Vi waveform, indicating clearly the value of the peak voltage. (ii)

The full-wave rectifier circuit shown in Figure Q1(d) has a center-tapped transformer. The load resistance, R is 100 2 and the output, V. waveform is given in Figure Q1(d). Assume practical silicon diode model. D ; 2 ): 1 R P. 5V OV Figure QI(d) (i) Calculate the DC load voltage, DC load current, and PIV of each diode. Find the peak input voltage, Vi and then sketch the Vi waveform, indicating clearly the value of the peak voltage. (ii)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
A full-wave bridge rectifier with a 236.86V p-p sinusoidal input has a load resister of 2KΩi. Draw the wave form that the load resistor R would see. ii. Assuming diodes are ideal, what is the dc voltage available at the load resistor? iii. What is the dc voltage available at the load if silicon diodes are employed? iv. Calculate the maximum current flow through the Diode D4 during conduction.
In a 1-phase full wave bridge rectifier with Vs = Vm sin ωt, with R load & ideal diodes. The expression for the average value of the output voltage is 2Vm/π Select one: True False
(Q1 ,b) Required Explain the applications-based comparison b/w FWBR & CT-FWR so that under what conditions you will choose the CTWR.? b. Interpret (using the circuit diagram & the waveform diagrams) the behavior of a controlled Half-Wave Rectifier during the negative half cycle of AC supply when it is connected with RL load in the following cases; a. Without Free-wheeling diode.
Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise?
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
please solve parts d and e Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise? d) Determine the input power (active)? e) Determine the power factor?
A three-phase, half-wave uncontrolled rectifier is fed from an ideal three-phase voltage source of 380V, 50 Hz. The load is resistive with R=15 2. Calculate: (a) The average output voltage and average load current of the rectifier. (b) The d.c. and a.c. power dissipations in the load. (c) The diode ratings. (d) What is the lowest ripple frequency of the output voltage waveform?
E.) The voltage on Figure Q1 is connected across a 0.15 2 resistive load. Calculate the power dissipated in this resistor. F.) Sketch the circuit for an ac supply input to a full-wave diode rectifier with a resistive load and no smoothing capacitor. G.) For the circuit in Question (F) calculate the average and rms voltages across the resistive load for an rms ac supply voltage of 115 V assuming no diode voltage drop.