In the design of beam for the limit state of collapse in flexure as per IS 456: 2000, let the maximum strain in concrete be limited to 0.0030 (in place of 0.0035) for this situation consider a rectangular beam section of width 300 mm, effective depth as 400 mm, area of tension steel used is 900 mm2. Material used is M20 concrete mix Fe415 grade steel (a) Limiting depth of neutral axis (b) Actual depth of neutral axis

In the design of beam for the limit state of collapse in flexure as per IS 456: 2000, let the maximum strain in concrete be limited to 0.0030 (in place of 0.0035) for this situation consider a rectangular beam section of width 300 mm, effective depth as 400 mm, area of tension steel used is 900 mm2. Material used is M20 concrete mix Fe415 grade steel (a) Limiting depth of neutral axis (b) Actual depth of neutral axis

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

A reinforced concrete T-beam has the following properties: Flange width, bf = 1350 mm Width of web, bw = 300 mm Gross depth, h = 500 mm Effective depth, d = 420 mm Concrete strength, f'c = 21 MPa Steel strength, fy = 415 MPa If the beam is reinforced with 3-20-mm-diameter bars at the bottom (in single layer), determine the resulting depth of rectangular stress block at ultimate stage (mm, 2 decimal places). What is the condition of failure? (Balanced, Tension controlled, Compression controlled, Transition). Calculate the design moment strength of a typical interior beam (kN-m, whole number).
A reinforced concrete T-beam has the following properties: Flange width, bf = 1,350 mm Width of web, bw = 300 mm Gross depth, h = 500 mm Effective depth, d = 420 mm Concrete strength, f’c = 21 MPa Steel strength, fy = 415 MPa 10. If the beam is reinforced with 3-20-mm-diameter bars at the bottom (in single layer), determine the resulting depth of rectangular stress block at ultimate stage. = mm (2 decimal places) 11. What is the condition of failure? = (Balanced, Tension controlled, Compression controlled, Transition) 12. Calculate the design moment strength of a typical interior beam. = kN⋅m (whole number)
A rectangular beam having a width of 300 mm has an effective depth of 600 mm. The totaldepth of beam is 680 mm. The beam is reinforced with 3-32 mm at the bottom. f c ’ = 27.6 MPa, and fy =415 MPa. Determine the following:1. The shear strength of concrete subjected to shear and flexure only if it is subjected to afactored moment Mu = 134 kN.m which occurs simultaneously with Vu = 223 kN. 2. The shear strength of concrete if the beam is subjected to an axial compressive force of268 kN. 3. The spacing of 10 mm shear reinforcement if the simple beam has a span of 6 m andsupports a factored uniform load of 150 kN/m including its own weight.
A beam has a flange width of 810mm and a slab thickness of 50mm. The width of the web section is 300mm and it has an effective depth of 550mm. It is reinforced at the bottom with a steel area of 1750mm2. fc’ = 20MPa, fy = 400MPa. The magnitude of the compressive force of concrete is ____kN
A rectangular concrete beam has a width of 400 mm and an effective depth of 700 mm. It is reinforced with five 28-mm diameter bars for tension only. Concrete strength is f's = 21 MPa and steel yield strength is fy = 275 MPa. Which of the following most nearly gives the depth of the rectangular compression stress block? A. 188.15 mm B. 151.93 mm C. 139.51 mm D. 118.58 mm
1. A simply supported beam 300 mm wide, 500 mm deep and spans 5.7 m supports a service super imposed dead load of 9 kN/m and service live load of 9 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the depth of equivalent rectangular stress block (mm) at ultimate stage. Write your answer in 2 decimal places only. 2. A simply supported beam 300 mm wide, 500 mm deep and spans 5 m supports a service super imposed dead load of 7 kN/m and service live load of 6 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
A rectangular beam with a width of (9536/1150)-in,and effective depth of (9536/900)in is Reinforced with a single high strength steel bar that has a cross- sectional area of 0.42 in2.The bar has a normal tensile strength of 145 ksi, linear stress-strain curve to failure, and a strain at failure of 1.8 percent. The concrete strength fc= 6000 psi. Calculate the nominal flexural strength of the section.
Answers should be in 3 decimal places 1) Determine the Cracking moment of the section below: 2) A rectangular reinforced concrete beam with width of 300mm and effective depth of 515 mm is reinforced with 4D32mm RSB. Using working stress analysis for cracked sections, find the maximum stress of concrete and steel, if the section is subjected to a moment equal to 106 mm kN-m. Use 8 as the modular ratio of the beam. 3) Given: b= 300 mm ; d= 425 mm; d’= 65mm; As’=2D25; As= 6D25 (two layers); fc’=28MPa and fy=345MPa. Solve for the Nominal Moment Capacity of the section, Mu.
A 395 mm diameter short concrete post has 6-600 mm² steel bars reinforcing it. E(steel) = 200 GPa , E(conc) = 15 GPa. Assume that the allowable stress to be σ(steel) =160 MPa, σ(conc) = 8 MPa.1. Find the maximum allowable actual stress in steel. a. 203.12 MPab. 154.23 MPac. 106.64 MPad. 95.235 MPa3. Find the maximum allowable load. a. 1335.104 kNb. 1245.120 kNc. 1654.100 kNd. 1323.105 kN
A cast iron 3m long is completely filled with concrete and used as a vertical strut. If the externaldiameter of the tube is 450mm and the wall is 35mm thick, determine the maximum compressiveload the composite strut can support if the stress in the concrete is not 2N/mm2? By how muchshould the strut shorten under this load? For cast iron EA= 100GN/m2 and for the concrete EB=10GN/m2?
A prestressed rectangular beam 0.50m x 0.75m has a simple span of 10m and is loaded with a uniform load of 45 kN/m including its own weight. The prestressing tendon is 0.225 m from the bottom and produces an effective prestress of 1600 kN. Compute the fiber stress distribution in the concrete at midspan (top fiber) due to axial and transverse loading. Select one:a. 13.94 MPab. 11.15 MPac. 5.85 MPad. 7.81 MPa
4. A reinforced concrete T-beam has the following properties: Flange width, bf = 1,350 mm Width of web, bw = 300 mm Gross depth, h = 500 mm Effective depth, d = 420 mm Concrete strength, f’c = 21 MPa Steel strength, fy = 415 MPa a. If the beam is reinforced with 3-20-mm-diameter bars at the bottom (in single layer), determine the resulting depth of rectangular stress block at ultimate stage. = ____ mm (2 decimal places) b. What is the condition of failure? = ____ (Balanced, Tension controlled, Compression controlled, Transition) c. Calculate the design moment strength of a typical interior beam. = ____ kN⋅m (whole number)