In the figure, suppose the length L of the uniform bar is 2.9 m and its weight is 170 N. Also, let the block's weight W = 270 N and th angle 0 = 37°. The wire can withstand a maximum tension of 360 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A?

In the figure, suppose the length L of the uniform bar is 2.9 m and its weight is 170 N. Also, let the block's weight W = 270 N and th angle 0 = 37°. The wire can withstand a maximum tension of 360 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A?

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 68P: An aluminium (=2.7g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the...

See similar textbooks

Similar questions

a thin horizontal bar AB of negligible weight and length L is hinged to a vertical wall at A and supported at B by a thin wire BC that makes an angle u with the horizontal. A block of weight W can be moved anywhere along the bar; its position is defined by the distance x from the wall to its center of mass. As a function of x, find (a) the tension in the wire, and the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A.
a uniform beam with a weight of 60 N and a length of 3.2 m is hinged at its lower end, and a horizontal force of magnitude 50 N acts at its upper end.The beam is held vertical by a cable that makes angle u = 25° with the ground and is attached to the beam at height h = 2.0 m. What are (a) the tension in the cable and (b) the force on the beam from the hinge in unit-vector notation?
A 2.4 m ladder rests on a vertical wall as shown in the figure. The ladder has 7 rungs and the rungs are spaced 0.30 m apart, and the top and bottom rungs are 0.30 m from their respective ends of the ladder. Surfaces at A and B both have the same coefficient of friction. If a worker weighs 360 N and stands on the middle rung, determine the minimum value of the coefficient of friction so that the ladder does not slide. Neglect the weight of the ladder.
a 50.0 kg uniform square sign, of edge length L=2.00m, is hung from a horizontal rod of length dh = 3.00 m and negligible mass. A cable is attached to the end of the rod and to a point on the wall at distance dv = 4.00 m above the point where the rod is hinged to the wall. (a) What is the tension in the cable? What are the (b) magnitude and (c) direction (left or right) of the horizontal component of the force on the rod from the wall, and the (d) magnitude and (e) direction (up or down) of the vertical component of this force?
A weight (with a mass of 71 kg) is suspended from a point near the right hand end of a uniform boom with a mass of 51 kg. To support the uniform boom, a cable runs from this same point to a wall (the left-hand vertical coordinate y = 7, x = 6) and by a pivot on the same wall at an elevation of 3 m. Calculate the tension T in the cable. The acceleration of gravity is 9.8 m/s2 Answer in units of N.
Suppose three forces with magnitudes of 198 N, 275 N, and 205 N are placed in equilibrium. If the 205-N force acts in the +y-direction, what is one of the two configurations in the xy-plane that the remaining forces may have? Give numerical values for the angles.
overhead view of a rigid rod that turnsabout a vertical axle until the identical rubber stoppers A and B are forced against rigid walls at distances rA = 7.0 cm and rB = 4.0 cmfrom the axle. Initially the stoppers touch the walls without beingcompressed.Then force of magnitude 220 N is applied perpendicularto the rod at a distance R = 5.0 cm from the axle.Find the magnitudeof the force compressing (a) stopper Aand (b) stopper B.
suppose the length L of the uniform bar is 3.4 m and its weight is 180 N. Also, let the block's weight W = 310 N and the angle 0 = 41°. The wire can withstand a maximum tension of 440 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A?
A bar weighing 26.0 N is supported horizontally on each end by two hangingsprings, each 15.0 cm long, with spring constants 0.970 N/cm and 1.45 N/cm,respectively. The bar is 6.00 m long and has a center of mass 2.00 m from thespring with constant 0.970 N/cm. How far does each spring stretch?
A uniform horizontal beam 5.00 m long and weighting 3.03 102 N is attached to a wall by a pin connection that allows the beam to rotate. Its far end is supported by a cable that makes an angle of 53.0° with the horizontal (Figure (a)). If a person weighing 6.05 102 N stands 1.60 m from the wall, find the magnitude of the tension in the cable and the force exerted by the wall on the beam. T = N Rx = N Ry = N Even if we selected some other axis for the torque equation, the solution would be the same. For example, if the axis were to pass through the center of gravity of the beam, the torque equation would involve both T and Ry. Together with Equations (1) and (2), however, the unknowns could still be found—a good exercise. In this example, notice the steps of the Problem-Solving Strategy could be carried out in the explicit recommended order.QUESTION What happens to the tension in the cable if the man in Figure (a) moves farther away from the wall? The tension would…
A person is standing on a section of uniform scaffolding as shown in the figure. The section of scaffolding is L = 1.50 m in length, has a ms = 24.5 kg mass and is supported by three ropes as shown. Determine the magnitude of the tension in each rope when a person with a weight of Wp = 640 N is a distance d = 0.700 m from the left end. magnitude of T1 N magnitude of T2 N magnitude of T3 N
A ladder of uniform density and mass m rests against a frictionless vertical wall, making an angle of 60.0° with the horizontal...