Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable CD is required for static equilibrium in the position shown? What is the tension Tin cable CD? T A 43° D 3.6' B 70 lb

Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable CD is required for static equilibrium in the position shown? What is the tension Tin cable CD? T A 43° D 3.6' B 70 lb

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.35P: Find the smallest value of P for which the crate in the Prob. 4.34 will be in equilibrium in the...

See similar textbooks

Related questions

Q: Determine factor of fafety ?

A: Given; Principal stress at point in a critical section of a m/c component are; σ1= 80 MPa σ2= 5…

Q: A reciprocating compressor delivers 0.1 kg/s of air at a pressure of 12 bar. The air enters the…

A: Given Mass flow of compressor = 0.1 kg/s Pressure of compressor = 12 bar Inlet pressure = 1 bar…

Q: (b) A 945L of 2,4-D in acetone has spilled, contaminating an area of soil approximately 300m² and 60…

Q: a) As shown in Figure A2-a, a piston-cylinder assembly with two set of stops contains a mass of 3 kg…

Q: A solid circular shafts is made of the 650°C temper 300-M steel with properties shown in the table.…

Q: If |A + B| = |A – B| then, the angle between A and B is: (a) 0° (c) 60° (b) 90° (d) 180°

A: Consider the following: A = Magnitude of A → B = Magnitude of B → θ = Angle between two vectors…

Q: Q6: Determine the Miller Indices for directions (Three only) and plane following: Nijm ² 2/m B LA of

Q: *) Determine the resultant of forces system shown in Figure below and locate it with respect to…

A: For the given system of forces, we have to find the magnitude of the resultant and its location with…

Q: Find the resultant of two forces hown in Figure and its direction with X axis sing Sine and Cosine…

Q: View Policies Current Attempt in Progress A force F of magnitude 810 lb is applied to point C of the…

Q: (B) Construct the analytic function ƒ(z) = u(x, y) + iv(x, y) of which the real part is: u(x, y) =…

Q: The body is formed of slender rod and rotates about a fixed axis through point O with the indicated…

Q: Find the absolute pressure in kPa at a depth of 7 m below the free surface of oil of SG = 0.74 if…

Q: The 470-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

Q: Determine the resultant of forces system shown in Figure below and locate it with respect to point…

A: GIVEN DATA- A FORCE SYSTEM SHOWN IN FIG, WE HAVE TO FIND RESULTANT OF IT AND ITS POSITION WITH…

Q: Problem (1): A large vacuum tank, held at sokf -absolute. Suck, sea-level standard air through a…

A: Given Data The pressure inside the tank is: P2=60 kPa The nozzle throat diameter is: d=3 cm=0.03 m…

Q: Determine the resultant of forces system shown in Figure below and locate it with respect to point…

A: ◆ The resultant of force system is 100 kN. ◆ It's location with respect to point A is 16.8 m.

Q: The actual trace of machined surface examined by surface profilometers is shown in the figure, me…

Q: Products possess (shows) better reproducibility in metal forming at forming temperature condition.…

A: Product posses better reproducibility in metal forming at cold forming temperature conditions. Cold…

Q: Q.1 Find the resultant of two forces shown in Figure and its direction with X axis using Sine and…

Q: Model by mechanical circuit. 2/1/2 3 quinq -- 3

A: Given Mass = m Spring constant = k Length = L Find Equation of…

Q: Determine the reactions in C on member ACD as shown in figure? 800 KN 5 m + 4m 6 m D 8 m E 600 KN 3…

A: Find Reactions at C.

Q: a) A gas is trapped in a piston-cylinder device. The initial pressure and temperature of the gas are…

Q: Q1) The angular velocity of the radar gun at point O is è = 0.2 rad/s when 0-40°, and the radius of…

A: The given data: θ˙ = 0.2 rad/sθ = 40°Radius of the road = r = 500 m

Q: 뜰 지 2 I 2k m 2m k F(t) 3 2c k

A: For solution refer below images.

Q: A steel plate 30 mm thick with a thermal conductivity k = 50 W/m K has a heat transfer rate of 125…

A: Note: As per policy we can solve the first question from your choice from multiple questions. Please…

Q: The Aircraft has a ratio of the lift force L to the drag force D for the simple airfoil is LD = 10.…

Q: o) Find the moment of force about G.2 point A as shown in Figure? 10 m B 90° 8 m 20° 1000 KN C

A: Given:F=1000 KNθ=20°

Q: A force F = (6î - 8j +10k) N produces an acceleration of 1 m/s² in a body. The mass of body would…

A: From the data given in question, Force F → = 6 i - 8 j + 10 k Acceleration of body = a = 1 m/s2…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

Q: b) What are the types of cast iron according to their microstructure? Explain with drawing.

Q: Determine the rate of heat transfer and the overall heat transfer coefficient for the composite wall…

Q: The throttle-control lever OA rotates in the range 0 ≤ 0 ≤ 90°. An internal torsional return spring…

Q: Air initially at 101.325 kPa, 30°C db and 40% relative humidity undergoes an adiabatic saturation…

Q: C- A rigid 1 m³ tank contains nitrogen gas, initially at 10 bar, 27 °C. Heat transfer to the gas…

A: Write the given data. V1=1 m3P1=10 bar=P2T1=27 °C=27+273=300 KT2=400 K

Q: As shown in the figure, y and for v = 15 m/s Calculate h. River N 40 m PRO 5m B

Q: Question 1 Water enters the heat exchanger at 20°C and leaves at 35° What is the log mean…

Q: 3 EW) 24. A centrifugal clutch has four blocks which slide radially in a spider keyed to the driving…

Q: What is the COP of an ideal heat-operated refrigeration cycle that receives the energizing heat from…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load Pat…

Q: Determine the resultant of forces system shown in Figure below and locate it with respect to point…

A: To determine the resultant and its location from Point A.

Q: B- Consider a steam power plant operating on the simple ideal Rankine cycle. Steam enters the…

Q: A worm running at 2000rev/min is to drive a worm wheel at 200 rev/min and to transmit to it 15kW.…

Q: KIN along the axis of a shaft is takon consisting of the frustum of a cone. The outer and inner…

Q: Two rods and one cable are attached to the supports at O. If two of the forces are as shown,…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

Q: (20%) Find the resultant of two forces shown in Figure and its direction with X axis using Sine and…

A: given: Two forces acting through origin F1 = 750 KN acting at angle 22o from positive X-axis F2 =…

Q: Determine the magnitude of the vector difference V = V₂ -2V₁ and the angle 0, which V' makes…

A: Given

Q: The Aircraft has a ratio of the lift force L to the drag force D for the simple airfoil is LD = 10.…

Q: Nitrogen at 120 kPa and 30°C is compressed to 680 kPa in an adiabatic compressor. Calculate the…

A: Given that: For nitrogen gas, P1 = 120 kPa, T1 = 30 oC P2 = 680 kPa Process 1-2 follows adiabatic…

Question

Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable CD is required for static equilibrium
in the position shown? What is the tension Tin cable CD?
↑
A
43°
D
3.6'
Answers:
LCD =
i
TCD
i
B
70 lb
ft
lb

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 40-kghomogeneous disk is placed on a frictionless inclined surface and held in equilibrium by the horizontal force P and a couple C (C is not shown on the figure). Find P and C.
The 14-kN weight is suspended from a small pulley that is free to roll on the cable. The length of the cable ABC is 20 m. Determine the horizontal force P that would hold the pulley in equilibrium in the position x=5m.
Find the smallest value of P for which the crate in the Prob. 4.34 will be in equilibrium in the position shown. (Hint: A rope can only support a tensile force.)
The uniform bar AB of weight W and length L is pinned to a sliding collar at A and to the sliding rod BD at B. The spring wound around rod BD has a stiffness k and is undeformed when rod AB is in the position =0. Determine the expression for the angle (other than =90 ) at equilibrium and investigate the stability of equilibrium for this position.
Draw the FBDs for the entire structure and the member BDE. Count the total number of unknowns and the total number of independent equilibrium equations. Note that the cable that supports the 1200-lb weight runs over a smooth peg at D.
The bar ABC is supported by three identical, ideal springs. Note that the springs are always vertical because the collars to which they are attached are free to slide on the horizontal rail. Find the angle at equilibrium if W = kL. Neglect the weight of the bar.
The stiffness of the ideal spring that is compressed by the slider C is k = 250 N/m. The spring is unstretched when =20. When the mass m is suspended from A, the system is in equilibrium at =60. Determine the value of m and whether the equilibrium position is stable or unstable.
The spring attached to the homogenous bar of weight W is undeformed when =0. Determine the smallest spring stiffness k for which the =0 equilibrium position will be stable. Use W = 10 lb, a = 24 in., and b = 6 in. Assume that the spring remains horizontal, which is a valid approximation if is small.
The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
Draw the FBDs for the beam ABC and the segments AB and BC. Note that the two segments are joined by a pin at B. Count the total number of unknowns and the total number of independent equilibrium equations.
The mass of crate D is held in position by two blocks, B and C, which are attached to the ring at A. The angle that rope AC makes in a counterclockwise direction from the positive x-axis is theta=30 rad as shown. The mass of block B is equal to that of C, mB=mC=158 kg a) draw the free body diagram of the point of equilibrium b) write down the static equilibrium equations c) determine the angle phi and tge weight of block D f) why will point A be the midpoint between B and C? Explain e) if all three weights are equal can equilibrium be maintained?
Determine the force in the cable OC and the elongation of the spring OA, OB necessary to support a box of mass (M) 400 kg as shown in the figure below. If a = 4 m, b = 5 m, c = 3 m, k1= 5000 N/mm and k2= 4000 N/mm. All calculation using equilibrium of particles equation and must be in Newton (N) and with FBD