In the system shown, the water discharge flow rate of 0.0025 m³/s is delivered through the 8 cm asphalted cast iron pipe? €=0.12 Calculate the total losses in the pipe For minor losses, take K for the Entrance: 0.34 Exit: 0.24 Open global Valve: 0.44 Bend radius: 0.04 Elbow = 0.14 Half open gate valve: 0.64 Water density=1000 kg/m³ and viscosity is 0.001 N s / m² Use your last three digits of your ID number for the pipe length in m 2 22 = 5 m Sharp entrance Open globe valve Screwed regular 90° elbow bend radius 8 cm diameter Sharp exit O Half-open gate valve 2₁ = 20 m

In the system shown, the water discharge flow rate of 0.0025 m³/s is delivered through the 8 cm asphalted cast iron pipe? €=0.12 Calculate the total losses in the pipe For minor losses, take K for the Entrance: 0.34 Exit: 0.24 Open global Valve: 0.44 Bend radius: 0.04 Elbow = 0.14 Half open gate valve: 0.64 Water density=1000 kg/m³ and viscosity is 0.001 N s / m² Use your last three digits of your ID number for the pipe length in m 2 22 = 5 m Sharp entrance Open globe valve Screwed regular 90° elbow bend radius 8 cm diameter Sharp exit O Half-open gate valve 2₁ = 20 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows naturally from a tank A located at 20 m above the ground level , to a ground leveltank B . The connecting pipeline between tank A and tank B has an equialent loss coefficient of K .Determine the flow rate Q= ? ( USE g= 10 m 2/s) Note that K0,5 : square root of K. ANSWER: 20 / K0,5 m3/s
A pipe experienced a total head loss of 15 m, determine thepressure difference from its starting point to discharge point inkPa.
Water flows through the galvanized iron pipe system whose diameter is 0.75 inches and flow rate is 0.020 cfs. Do you agree with the fact that friction losses in the straight parts of the piping system are negligible with respect to losses to fittings?
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. (DO NOT ROUND OFF)
Water at 20°C fl ows by gravity through a smooth pipe fromone reservoir to a lower one. The elevation difference is 60 m.The pipe is 360 m long, with a diameter of 12 cm. Calculatethe expected flow rate in m3/h. Neglect minor losses.
Determine the Reynold's Number and flow regime of an bil flowing through a 450-mm diameter pipe, if the flow rate is 0.40 m³/s. Note: Hoil = 0.025 Pa's and Scoil = 0.86).
Water (ρ=998 kg/m³, μ=1.02x10^-3 kg/ms) flows through a 598 m length of pipe with 150 mm in diameter at 60 L/s. Determine the pipe roughness, ɛ if the head loss is 49 m.
Two pipes, one circular and one square have the same cross-sectional area. Which has the larger hydraulic radius ? Show your solution to prove your answer
The horizontal pipe length is 180 m and the vertical pipe length is 24 m in the fire protection system, which is formed with a water tower and pipeline, 1 threaded 90 ° elbow (Kd = 0.9) on the pipeline and 1 slide valve at the pipe outlet (fully open position Kv = 0.2). Since the pipe material is cast iron and its diameter is 4 ”(101.6 mm), determine the maximum flow rate in the pipe considering the losses. Assume that the water level in the tower remains constant and the kinematic viscosity of the water is 1.124x10-6 m2 / s. Show your readings by drawing on the attached Moody diagram.
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m. the total length and diameter of the sunction and discharge pipe are 500 mm,1500 m and 300 mm, 1000 m respectively. assumme a head lose of 2 meters per 100 m length of the sunction pipe and 3m per 100 m length of the discharge pipe. what is the required horsepower of the pump?
04: Three pipes of diameters 300 mm, 200 mm and 400 mm and lengths 450 m, 255 m and 315 m, respectively, are connected in series. The difference in water surface levels in two tanks is 18 m. Determine the rate of water flow if coefficients of friction are 0.0075, 0.0078 and 0.0072, respectively, considering: (a) with minor losses, (b) without (neglecting) ‘minor losses.
Water is pumped through a 60-m-long, 0.3 –m-diameter pipe from a lower reservoir to a higher reservoir whose surface is 10 m above the lower one. The sum of the minor loss coefficients for the system is Kl = 1.5. When the pump adds 40 kW to the water the flowrate is 0.2 m3/s. Determine the pipe roughness.