In this circuit and graph, there are three different load lines plotted, representing three different values of load resistance in the amplifier circuit. Which one of the three load lines represents the largest value of load resistance(RLoad)? Road 20 V Input Ic (mA) 16 14 C 12 10 B 8 4 2 0 0 2 T 4 6 1-40 μA 30 μA la-20 A la-10 µA SμA 1₂-0μA 8 A B C O None of above V out T 10 12 14 16 VCE (V) 18 20 22

In this circuit and graph, there are three different load lines plotted, representing three different values of load resistance in the amplifier circuit. Which one of the three load lines represents the largest value of load resistance(RLoad)? Road 20 V Input Ic (mA) 16 14 C 12 10 B 8 4 2 0 0 2 T 4 6 1-40 μA 30 μA la-20 A la-10 µA SμA 1₂-0μA 8 A B C O None of above V out T 10 12 14 16 VCE (V) 18 20 22

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

A. Give 3 possible problems rn that can relate on electrical engineering and give a solution that can aware public.
proof the equation 10.8 which represents the gain of inversting amplifer ... the proof is already exist in page 621 but there are some expressions were missed before the equation 10.7, you should start this proof from the begining and adding that missed expressions.
Derive the appropriate equation for the electronic system with the operational amplifier as shown in the drawing and give the resistance values in the range 1-10 kOhm so that the system can follow the equation: U2 = - 1.5U11 + 2.5U12. Draw your equation using the Math tool, with superscript and subscript and then enter the values of resistance R1 and R2 according to the formula: {equation}; R1 = 1 kOhm; R2 = 1 kOhm
Figure 1 shows a well-known circuit configuration with the bypassed source resistor using an n-channel D-MOSFET with yos = 20µS. (iv) Calculate transconductance, gm and rd. (v) Calculate the input, Zi and output impedance, Zo for the circuit. (vi) Prove that the equation for the no-load Gain, AvNL, for the circuit is as follows: AvNL = -gm (RD X rd / RD + rd) (vii) Calculate the no-load gain AVNL. (viii) Find the value of VoNL if Vi = 30 mV.
The following amplifier (consider the case with a R_L load) consists of a channel JFET n. In the amplifier, the value of the DC source ({+ V} DD = 20 V) and of all resistors (shown in the schematic) and capacitors ( C1= C2= 20 µF) is known. At the same time, the JFET has the following specifications: IDSS= 10 mA and Vp= -3.5 V. The output resistance of the JFET is r_d = infinityΩ.AC analysis:The input signal VS is a small sinusoidal signal, at the same time it oscillates at a medium frequency, in such a way that the response is not affected by the capacitances. Get the circuit in small signal and do all the necessary procedure / demonstration. To determine:A) The transconductance gm at the operating point.B) The small signal equivalent circuit drawn conveniently.
Please answer correctly, I'll give upvote. In the given circuit, find the voltage gain and output impedance in terms of gm1, gm2, ro1, ro2, R1, and R2.
a) A source vs = 2 V with internal source resistance Rs =10 kΩ applies a signal to a5 gain inverting amplifier with R1 =20 kΩ and R2 =100 kΩ. find the voltage ofoutput and verify that if a load is connected it will receive less than 10 V. (b) Find the value atthat we should change R2 to compensate and obtain 10 V at the output. present calculations
Circuit with given BJTa) Calculate VE1, VE2 , VB1, VB2 , IE1 , IE2 values.b) Find the input and output impedance.c) Find the Current gain AND Voltage gain. VBE=0.7 V, VD=0.7 V , VCC=+20V, β=100R1=R2= 7 KohmsMAKE A DETAILED SOLUTION
Answer all subparts with explanation 1. A certain common-drain (CD) amplifier with Rs=1kΩ has a transconductance of 6000 µS. The voltage gain is a. 1 b. 6 c. 0.98 d. 0.86 2. A type of amplifier that operates in the linear region for 180 0 of the input cycle because it is biased at cutoff. a. CLASS B b. CLASS AB c. CLASS C d. CLASS A 3. The constant-current region of a FET lies between a. 0 and IDSS b. cutoff and pinch-off c. pinch-off and breakdown d. cutoff and saturation
Assume the resistor in the variable branch of the bridge circuit shown is R-ΔR instead of R+ΔR. 1. What is the expression for vo if ΔR≪R? 2. What is the expression for the percent error in vo as a function of R, Rf, and ΔR? 3. Assume the resistance in the variable arm of the bridge circuit shown is 9810 Ω and the values of R, Rf, and vin are the same as in Problem 5.50(b). What is the approximate value of vo? 4. What is the percent error in the approximation of vo when the variable arm resistance is 9810 Ω?
Kindly give correct answer Consider the biasing circuit shown. The β for the circuit is large. R3 = 1kΩ, R4 = 2kΩ. The stability factor varies between 10 and 11. Find the maximum and minimum values of R2.
Design a differential amplifier with tail resistor , using ±12V supplies such that Itail ≈ 4mA. Set RC1 = RC2 = 5kΩ. Ground the inputs and solve for RT. (My answer for RT is 2.8 kOhm)