) Isosceles triangles were used as the main geometric figure in the patches used to make a tent. The equal sides of these isosceles triangles were made to have a constant length of 6.7 ft. Varying sizes of the tent would mean a varying number of isosceles triangles needed. If the angle between the equal sides of the isosceles triangle increases at the rate of 8 rad/sec, determine the rate at which the area of the triangle is increasing when the angle is 75°. Enclose in boxes the function generated from this problem together with its derivative. These should be included in the summary of answers.

) Isosceles triangles were used as the main geometric figure in the patches used to make a tent. The equal sides of these isosceles triangles were made to have a constant length of 6.7 ft. Varying sizes of the tent would mean a varying number of isosceles triangles needed. If the angle between the equal sides of the isosceles triangle increases at the rate of 8 rad/sec, determine the rate at which the area of the triangle is increasing when the angle is 75°. Enclose in boxes the function generated from this problem together with its derivative. These should be included in the summary of answers.

Mathematics For Machine Technology

8th Edition

ISBN:9781337798310

Author:Peterson, John.

Publisher:Peterson, John.

Chapter31: Customary Vernier Calipers And Height Gages

Section: Chapter Questions

Problem 19A: The distance between the centers of two holes can be checked with a vernier caliper. The position of...

See similar textbooks

Similar questions

A goat is tethered to a barn by a 12-ft chain. If the chain is connected to the barn at a point 6 ft from one end of the barn, what is the area of the pasture that the goat is able to graze?
A calendar is determined by using each of the 12 faces of a regular dodecahedron for one month of the year. With each side of the regular pentagonal face measuring 4cm, the area of each face is approximately 27.5 cm2. a What is the total surface area of the calendar? b If the material used to construct the calendar costs 0.8 of a cent per square centimeter, what is the cost of the materials used in construction?
Four sets of equally spaced holes are shown in the machined plate in Figure 13-4. Determine dimensions A, B, C, and D to 2 decimal places. All dimensions are in millimeters. A=_B=_C=_D=_
The distance between the centers of two holes can be checked with a vernier caliper. The position of the caliper in measuring the inside distance between two holes is shown in Figure 29-10. To determine the setting on the caliper, subtract the radius of each hole (one-half the diameter) from the center distance. In Exercises 19 through 23, give the hole diameters and the distances between centers. For each, determine (1) the main scale setting and (2) the vernier scale setting. All dimensions are in inches.
The distance between the centers of two holes can be checked with a vernier caliper. The position of the caliper in measuring the inside distance between two holes is shown in Figure 29-10. To determine the setting on the caliper, subtract the radius of each hole (one-half the diameter) from the center distance. In Exercises 19 through 23, give the hole diameters and the distances between centers. For each, determine (1) the main scale setting and (2) the vernier scale setting. All dimensions are in inches 23. Note: Hole tolerances and center distance tolerances are shown. Maximum and minimum vernier scale settings are required.
The center of a circle of radius 2 in. is at a distance of 10 in. from the center of a circle of radius length 3 in. To the nearest tenth of an inch, what is the approximate length of a common internal tangent? Use the hint provided in Exercise 38. HINT: use similar triangles to find OD and DP. Then apply the Pythagorean Theorem twice.
A hot-air balloon is held in place by the ground crew at a point that is 21 ft from a point directly beneath the basket of the balloon. If the rope is of length 29 ft, how far above ground level is the basket?
A guy wire 25 ft long supports an antenna at a point that is 20 ft above the base of the antenna. How far from the base of the antenna is the guy wire secured?
The center of a circle of radius 2 inches is at a distance of 10 inches from the center of a circle of radius length 3 inches. To the nearest tenth of an inch, what is the approximate length of a common internal tangent? Use the hint provided in Exercise 38. HINT: use similar triangles to find OD and DP. Then apply the Pythagorean Theorem twice.
The larger circle is inscribed in a square with sides of length 4cm. The smaller circle is tangent to the larger circle and to two sides of the square, as shown. Find the length of the radius of the smaller circle.
This sheet metal section shown in Figure 5-5 has five sets of drilled holes: A, B, C, D, and E. The holes within a set are equally spaced in the horizontal direction. Compute the horizontal distance between two consecutive holes for each set. All dimensions are in inches. A=_B=_C=_D=_E=_
If line segment AB and line segment CD in the accompanying drawing are drawn to scale, what does intuition tell you about the length of these segments?