It is desired to pass water from point 1 to point 3 by means of a hydraulic pump, both tanks are open to the atmosphere, the diameter of the pipe is uniform. The external diameter has a value of 28 mm with a thickness of 2mm. If the friction losses are estimated to be 4N.m/N, it is known that the fluid velocity in the pipe is 3m/s What will be the flow rate flowing through the pipe?

Q: Water flowing in a horizontal pipe is at a pressure of 1.40 x 10^5 Pa at a point where its cross…

A:

Q: Water at 4.4oC with a density of 1000 kg/ m3 and a viscosity of 1.55 cP is to flow through a…

A:

Q: Water is to be pumped through 1500 ft of pipe from the lower to upper reservoir at a rate of 4…

A:

Q: Suppose we have planned to design a hydraulic system.In this aspect, the pump selection is to be…

A:

Q: The below figure shows a pump that transfers a steady stream of 35 API crude oil from an oil tanker…

A: Givenform the given figureρ=53 lbm/ft3μ=13.2 cpPv=4.0 psiaa=506 gpm

Q: Water is flowing in pipeline 600 mm in diameter, 1000-meter long. The pressure at entrance reads 30…

A: Given Data D=600 mm L=1000 m P1=30 kPa P2=16 kPa f=0.013

Q: A 250 mm diameter pipe carrying 30 l/s of water suddenly enlarges to 400 mm diameter

A:

Q: An oil of sp.gr 0.85 is flowing through a pipe of diameter 425 mm at the rate of 450 liters per…

A: Specific gravity of oil, s=0.85 Pipe diameter, d=425mm=0.425m Oil flow rate, Q=450L/s=0.450m3/s Pipe…

Q: The below figure shows a pump that transfers a steady stream of 35 API crude oil from an oil tanker…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: A sealed tank filled with a fluid which is maintained at 0.35 bar gauge and 20 0C. The fluid…

A:

Q: A large pressurized tank filled with air discharges into the atmosphere. The flow path is a short…

A: Given data,  From the diagram, Area of the nozzle, A3=π4dnozzle2…

Q: A simple loop has 850 gpm flowing into the loop. Pipe segment 1 is 6" schedule 10 pipe, 420 feet…

A: Given Data  1.Velocity of water = 850gpm=0.05363m3/sec 2. length of pipe L1 =420 ft;=128.016meter…

Q: A reservoir supplies water as shown in Fig. 1. The pipe system consists of 6 m of pipe and two 90°…

A:

Q: (Problem 2) Alcohol (specific gravity = 0.80) is flowing through a horizontal pipe which is 10…

A:

Q: A pipeline carrying 0.257 m/s water is reduced suddenly from 400 mm to 250 mm diameter (Take Cc…

A: Note: As per Bartleby guidelines only one question has to be solved. So upload other questions…

Q: A centrifugal pump operating at sea level develops 50 m of head at 1,200 rpm. It is used to pump…

A: Given data:

Q: A storage tank has hot water. This water at a temperature of 85 °C is pumped to a 600 cm height at a…

A:

Q: Water is flowing in a pipeline at 64 li/sec. If the diameter of the pipeline is 120 mm, calculate…

A:

Q: Oil (SG=0.82) entering a pump through an 8-inch diameter pipe at 4 psi has a flow rate of 3.5 cfs.…

A:

Q: . A mercury manometer attached to it shows deflection

A:

Q: A reciprocating pump has 350mm x 400mm cylinder running at 360rpm. If percent slip is 10%, what is…

A: Given data: Size of cylinder=350×400 mm2Slip=10% Need to determine the volumetric efficiency of the…

Q: A large tank is partly filled with water, the air space above being under pressure. A 2′′ hose…

A:

Q: d Box the final Answer ( Show all steps ) Question : A good curve-fit to the head vs. flow for the…

A:

Q: Water is to be pumped through 1500 ft of pipe from the lower to upper reservoir at a rate of 4…

A: Given:Length of pipe, L=1500 ft =457.2 mVolume flow rate, Q=4 ft3/s =0.113267 m3/sdiameter, d=8 in…

Q: Consider the surface of a pipe to be smooth with air flowing through it. The air flow rate (flowing…

A: An isothermal process is characterized by the equation- P1v1=P2v2 where, P1 is the pressure of the…

Q: is desired to pass water from point 1 to point 3 to run a fluid engine, pressure p1= 700kpa and…

A: Power to be Transmitted = {density * flow * ( total required head)} / efficiency total head required…

Q: (a) hot water outlets of diameter 20mm. All outlets are connected to a single main line pipe running…

A: Given : Outlet flow rate, q = 14 l/min = 0.014 m3/min Outlet diameter, D = 20 mm To find : Diameter…

Q: 4: A 60 mm diameter sharp edged orifice is placed in a pipe line to measure flow rate. If the…

A:

Q: (Problem 3) A horizontal water pipe is reduced in size from 18 inches in diameter from point A to 6…

A:

Q: A venturimeter with 75 mm diameter throat is placed in a 150 mm diameter pipeline carrying water.…

A:

Q: A fountain and a water tank will be powered by water from a nearby lake. The elevations and pipe…

A:

Q: In a lab experiment, it has been found that the velocity profile in a pipe where the flow is…

A:

Q: a) The discharge of water through a 140° bend, is 30 litres/s. The bend is lying in the horizontal…

A:

Q: Water flows steadily through a pipe with ID 35 mm. This pipe expands suddenly to an inner diameter…

A:

Q: A pipe bends through 900 from its initial direction as shown in fig.13. The pipe reduces in diameter…

A: The flow in pipe will have to follow continuity equation: A1V1 = A2V2 The flow must also follow…

Q: 1. For a given pump, the diameter, the gauge pressures at the inlet and outlet are −30 ×…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: Suppose it takes ½ hour to fill a 16 ft x 32 ft x 7 ft swimming pool from a 2.0 in. diameter pipe,…

A: Time required to fill the swimming pool, t=12hr=12*3600 seconds=1800 secVolume of the swimming pool,…

Q: (a) (b) (link to image) a) Water leaves a large tank through a sharp edged circular hole. The hole…

A:

Q: A 200 mm diameter pipeline is laid on the ground. At a particular point, the piezometric head is 20…

A: Given:Diameter of pipe, d=200 mm or 0.2 mPiezometric head=20 mTotal energy head=26 m

Q: A manufacturing company uses a 100 bar hydraulic power system which supplies 10 liter/minute of oil…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A large pressurized tank filled with air discharges into the atmosphere. The flow path is a short…

A:

Q: 5. A variable area flowmeter (rotameter) is used to find the flow rate of water at room temperature.…

A: Given: Height of the log of the rotameter=18 inch And height of the floater mid plane from…

Q: Water (density 62.4 lb/ft3, viscosity = 1 cP) is pumped from a large reservoir on the floor at a…

A:

Q: A horizontal 90° elbow connects two 300 mm diameter pipes. The rate of water flow is 180L/s. The…

A:

Q: A sprinkler system pumps water through a large pipe inlet with a diameter (di). The pipe then breaks…

A: (b) To find: The expression for gauge pressure at point A. Concept used: The continuity equation for…

Q: Q1: An oil with a viscosity of µ = | 0.37 and density p=860 flows in a m m pipe of diameter D=…

A: Given: μ=0.37 Pa-sρ=860 kg/m3D= 0.035 mQ=4×10-5 m3/s To Find: a) dP for L=17m b) steepness of pipe…

Q: The diameter of the discharge pipe is 7in and that of intake pipe is 9in. The pressure gage at…

A:

Q: A pump with a 400 mm diameter suction pipe and a 350 mm discharge pipe is to deliver 20,000 liters…

A:

Q: A reservoir supplies water as shown in Fig. 1. The pipe system consists of 6 m of pipe and two 90°…

A: In the given system hydrostatic head of the reservoir is converted into a velocity head in the pipe.…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.