A pump with a 400 mm diameter suction pipe and a 350 mm discharge pipe is to deliver 20,000 liters per minute of 15.6°C water. Calculate the pump head in meters if suction gauge is 7.5 cm below pump centerline and reads 127 mmHg vacuum and discharge gage is 45 cm above the pump centerline and reads 75 kPa.

A pump with a 400 mm diameter suction pipe and a 350 mm discharge pipe is to deliver 20,000 liters per minute of 15.6°C water. Calculate the pump head in meters if suction gauge is 7.5 cm below pump centerline and reads 127 mmHg vacuum and discharge gage is 45 cm above the pump centerline and reads 75 kPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) thepump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) the pump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
A pump with a shaft input of 8.62 kw and an efficiency of 72 % is connected in a water line carrying 150 li / s. The pump has a 15 cm diameter suction line and a 12 cm diameter discharge line. The suction line enters the pump 2.3 m below the discharge line. For a suction pressure of 84.6 KN/m², calculate the pressure at the discharge flange.
1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
In a test of the centrifugal pump shown in Fig. , thefollowing data are taken: p1= 100 mmHg (vacuum) andp2 = 500 mmHg (gage). The pipe diameters are D1 = 12 cmand D2 = 5 cm. The flow rate is 180 gal/min of light oil(SG = 0.91). Estimate (a) the head developed, in meters,and (b) the input power required at 75 percent efficiency.
Asap; An impulse turbine is used to produce hydroelectric power. The average radius of the Pelton wheel is 2.0 m, and the jet velocity is 103 m/s from a nozzle of exit diameter equal to 0.318 m. The turning angle of the buckets is 165°. Take the density of water to be 998 kg/m^3. Calculate the ideal shaft power in MW.
A centrifugal pump pumps water at a flow rate of 7 m³/s to a height of 10 m. If the pump works at the best efficiency point, find the pump impeller diameter, pump speed, the best efficiency value of the pump, the head at the best efficiency value, and the specific speed of the pump, given that CQ=0.15 CH=6 CP=0.75.
The suction diameter of 60 mm reads 2 psi vaccum and 50 mm diameter discharge with 250kpag. The suction water level is 5 m above water pump centerline and discharge water levelis 25 m above water pump centerline and discharge is 2 m. If discharge is 0.01 m^3/s, findthe horsepower needed to pump the water for 80 percent pump efficiency.
You are asked to calculate a rotadynamic pump with a total manometric head of 11 mss and demand flow of 19 in lt / s, which will meet the daily water need of a facility, and which can rotate at 1450 rpm for its drive, using a three-phase electric motor. Since the density of the water to be transported is 1000 kg / m3; a) Calculate the pump organs.
24 m3/s of water flowing through the fixed vanes of a turbine, has a tangential velocity component of 2 m/s at a radius of 1.25 m and the impeller turning at 240 rpm discharges in an axial direction. Neglecting losses, what is head on the turbine.
A fan can deliver a total pressure of 437 mm of water gage. The boiler requirement is 14,078 m^3/hr of standard air and the mechanical efficiency is 89%. Determine the brake power in kW.
If a pump discharges 284 liters per minute of water whose density is 985 kg/m3; find a) the mass flow rate in kg/min, and b) the total time required to fill a vertical cylindrical tank 3.05m in diameter and 3.05m high.