Steady, incompressible and inviscid water flows inside the given system, if the force F is needed to hold thesystem stationary, what is the work W (W=F x L) joule is needed to move the systema distance L=6.3 m.V1=3 m/sA1=0.1 mp1=200 kpa2 mA2=0.2 mENG10:06US 07/05/2DELLFZF8F9F10F11F12PrtScrInsertDeletePgUpPgDn

Solution : Given data : V1 = 3 m/sA1 = 0.1 m2 A2 = 0.2 m2P1 = 200 kpa L = 6.3m we…

Answered: joule is needed to move the system a…

Engineering

Mechanical Engineering

joule is needed to move the system a distance L=6.3 m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please solve it correctly,Urgent. Question: The discharge pressure of a water pump is 9, 000 kPa. The temperature is 150 deg deg C and density is 917 kg/m3. What is the equivalent pump head in meters? A. 11.005 m B. 1,000.5 m C. 1,050.5m D. 1, 100.5 m
A bicycle tire is fi lled with air at an absolute pressure of169.12 kPa, and the temperature inside is 30.0 °C. Supposethe valve breaks, and the air starts to exhaust out of the tireinto the atmosphere (pa = 100 kPa absolute and Ta =20.0 °C). The valve exit is 2.00 mm in diameter and is thesmallest cross-sectional area of the entire system. Frictionallosses can be ignored here; one-dimensional isentropicflow is a reasonable assumption. (a) Find the Machnumber, velocity, and temperature at the exit plane of thevalve (initially). (b) Find the initial mass flow rate out ofthe tire. (c) Estimate the velocity at the exit plane using theincompressible Bernoulli equation. How well does thisestimate agree with the “exact” answer of part (a)? Explain.
Assume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m3 (0.002377 slug/ft3) and 1.01 × 105 N/m2 (2116 lb/ft2), respectively. Consider a venturi with a throat-to-inlet area ratio of 0.8, mounted on theside of an airplane fuselage. The airplane is in flight at standard sea level.If the static pressure at the throat is 2100 lb/ft2, calculate the velocity ofthe airplane.
An orifice on vertical wall has a head of 1.13m of oil ( sp.gr.=0.89). It discharges 6192N of oil in 88 seconds . The trajectory measures yield x = 2.4m and y = 1.37m . Assuming the area of the opening is 25cm2, Calculate Coefficient of Contraction, Coefficient or Velocity
A fan draws air at rest and propels it 45 meters through a rectangular duct measuring 200 by 300 mm. At a rate of 0.6m3/s, air enters at 15°C and 750 mm Hg absolute pressure. What is the required theoretical power?
A centrifugal pump having a head-capacityrelationship given by the equation ha=180 –6.10 X 10-4 Q2, with ha in feet when Q is ingpm, is to be used with the system shownin the figure, For Z2-Z1= 50 ft, what is theexpected flowrate if the total length ofconstant diameter pipe is 600 ft and thefluid is water? Assume the pipe diameter tobe 4 inch and the friction factor to be equalto 0.02. Neglect all minor losses.
In Prob. it would be difficult to solve for Ω because of itappears in all three of the dimensionless pump coefficients.Suppose that, in Prob. 5.61, Ω is unknown but D = 12 cmand Q = 25 m 3 /h. The fluid is gasoline at 20 ° C. Rescale thecoefficients, , to make a plot ofdimensionless power versus dimensionless rotation speed.Enter this plot to find the maximum rotation speed Ωforwhich the power will not exceed 300 W.
Air velocity in a duct is measured as 38.2 m/s by a pitot tube. Density of flowing air 1.3 kg/m3. If the pressure difference recorded by the pitot static tube is 0.1 m of water, calculate the coefficient of velocity of the pitot static tube. A Figure or Free Body Diagram will be much appreciated. Thank you
A pump delivering 0.23 m3/s of water has a 304.8mm diameter suction flange and 254mm discharge flange. The suction pipe is 3.66m long and the discharge pipe is 22.86m long. Neglecting the turbulence losses in the pipe, find: a.) the head which the pump must deliver ( in meters ) b.) the motor power in KW required if the efficiency is 80%, c.) the reynold’s number and type of flow in the suction pipe d.) the reynold’s number and type of flow in the discharge pipe
Water is pumped between two reservoirs in a pipeline with the following characteristics; (d=275mm, L= 50m, = 0.02, minor loss is neglected. The pump performance curve is approximated by the equation: H,=21.5-6507 Where H, is in meters and Q is in m/s. Determine the discharge O and pump head /7 when two pumps in series are used for total static head (4Z=25m).
Pipe A, 30 cm in diameter, branches into two pipes B and C. Pipe B is 15 cm in diameter and pipe C is 7.5 cm in diameter. If the flow in A is divided as follows 2/3 goes to B and 1/3 goes into C, what is the discahrge in pipe A, if the velocity must not exceed 3 m/s in any of the pipes?
In a pipe of diameter 300mm the center line velocity and the velocity at a point 100mm from the center, as measured by pitot tube are 2.4 m/s and 2.0 m/s respectively. Assume the flow in the pipe to be turbulent find: 1-Dischrge through the pipe,2-Coefficient of friction, 3 Height of roughness projections.Please do not waste my question solve with correct answers only.