kindly help me with this one. Write your answer with four decimal places and enclose them in a box. Solve as neatly as possible. A sheet of Invar is 0.60in. thick and the temperatures at the two faces are 402degF and 222degF. Compute (a) the heat flux through the Invar sheet; (b) heat loss per hour if the are of the sheet is 6.4 square feet; (c) heat loss per hour if pyrex glass instead of Invar is used;

kindly help me with this one. Write your answer with four decimal places and enclose them in a box. Solve as neatly as possible. A sheet of Invar is 0.60in. thick and the temperatures at the two faces are 402degF and 222degF. Compute (a) the heat flux through the Invar sheet; (b) heat loss per hour if the are of the sheet is 6.4 square feet; (c) heat loss per hour if pyrex glass instead of Invar is used;

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.26P

See similar textbooks

Similar questions

A square steel alloy plate 400 mm on a side has a 90-mm-diameter circular hole at its center. The plate is heated from 20°C to 45°C. The final diameter of the hole is ____ mm.
A pipe has inner diameter 31 mm, outer diameter 106 mm, and length 4.3 m. Its thermal conductivity is 476 W m-1 K-1. The inner and outer surface temperatures are 103°C and 18°C, respectively. What is the heat transfer rate from inside to outside? (Answer in W and round your answer to the nearest integer) Handwritten please
An uninsulated steam pipe passes through a room in which the air and walls are at 25°C. The outside diameter of the pipe is 88 mm, and its surface temperature and emissivity are 200°C and 0.80 respectively. If the coefficient associated with free convection heat transfer from the surface to the air is 15W/m2-k, what is the rate of heat loss for a 5 meter pipe? Round your answer to 2 decimal places.
a shaft made of aluminum is 21 mm in diameter at the temperature of 22 degrees .the co-efficient of thermial expansion for aluminum is given on the table . If it must be expansion-fitted in a hole. Determine the temperature to which the shaft must be cooled
Electrical current flows through a cylindrical cable with a diameter of d = 4 mm generating thermal energy at a uniform rate of 1.6x107 W/m3. There is an insulation of t = 3 mm thickness with a conductivity of 0.2 W/mK. The system is exposed to convection as shown in the figure. Be careful, the outer diameter of the system with insulation becomes d + 2t. Calculate the surface temperature, Ts of the cable in °C. Round your answer to the nearest integer value and write only the numerical value in the provided box, not the units.
The 12ft x 14 foot room illustration in figure 1.6a has an exterior wall at a surface temperature of 60°F, a window surface temperature of 40°F (double glazing on a cold day). The two interior wall surfaces are a temperature of 72°F. Determine the MRT sensation of a person standing in the center of the room. (See figure 1.6 below) Round your values to the nearsest hundreth decimal place (0.00). You will need to upload your mathematical work in question 4.
What is the rate of heat transfer through a piece of Celotex 3 ft by 8 ft by 1 in. in thickness, if the temp of one surface is 80°F and of the other side is 60°F? thermal conductivity of Celotex in AES = 0.028. Pls determine the temperature gradient and the direction of the heat transfer as well.
The bottom of a 50mm diameter, 2mm thick metallic induction heater is 120C while its thermal conductivity is 60 W/m-C. The voltage and current flowing into the heater are 220V and 5A, respectively. Find the temperature at the top portion of the pan. Sketch diagram and show pertinent solutions. Box your final answer and express numerical values in 2 decimal places
1.3 A furnace wall is to be constructed of brick having standard dimensions of Two kinds of material are available. One has a maximum usable temperature of 1040°C and a thermal conductivity of 1.7 W/(m K), and the other has a maximum temperature limit of 870°C and a thermal conductivity of 0.85 W/(m K). The bricks have the same cost and are laid in any manner, but we wish to design the most economical wall for a furnace with a temperature of 1040°C on the hot side and 200°C on the cold side. If the maximum amount of heat transfer permissible is 950 , determine the most economical arrangement using the available bricks.
2.50 Compare the rate of heat flow from the bottom to the top of the aluminum structure shown in the sketch below with the rate of heat flow through a solid slab. The top is at v, the bottom at . The holes are filled with insulation that does not conduct heat appreciably.
What is the rate of heat transfer, temperature gradient, and the direction of the heat transfer through a piece of Celotex 3 ft by 8 ft by 1 in. in thickness, if the temp of one surface is 80°F and of the other side is 60°F? - thermal conductivity of Celotex in AES = 0.028.
Answer within 10 minutes : The temperature at the inside surface of an oven is 460 oF. The inside wall of the oven is made of brick and is 8 inch thick. The thermal conductivity of the brick is 2.2 Btu/hr.ft2.(oF/ft). The outside of the oven is covered with a 3-inch layer of asbestos as insulation, which has a thermal conductivity of 0.11 Btu/hr.ft2.(oF/ft). If the outer surface of the insulation has a temperature of 100 oF , calculate the amount of heat lost through 2 ft2 of wall area in 3 hours.