V3 Using the information provided below, calculate the Km and Vmax values for this kinetics trial.Also, determine the kcat value for [E] = 0.05µM. Pay attention to Sig Figs and to Units.Km ValueVmax Valuekcat Value0.4y = 0.6882x + 0.0736V1/S1/V0.3mMmM/min1/mMmin/mM3.660.3330.295-0.25.120.2000.23076.180.1430.1736.980.1110.143117.610.0910.131-0.2 -0.10.10.2 0.3 0.41/S (1/mM)

Answered: Image /qna-images/answer/ff669325-dbb7-4d7d-ac82-293550165a5b.jpg

Answered: Km Value Vmax Value kcat Value

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter30: Capillary Electrophoresis, Electrochromatography, And Field-flow Fractionation

Section: Chapter Questions

Problem 30.6QAP

See similar textbooks

Similar questions

If 5 µM enzyme was used to obtain the data in the summary plot below, V-max = ________________ µM sec-1 and Km = ____________ µM for this enzyme (Enter numeric values to the nearest integer; Do NOT write units.)
Q) water hardness of each trial and average ppm with calculation, please. Hard Water Trial 1 Hard Water Trial 2 Hard Water Trial 3 Initial Syringe Reading 1.0ml 1.0ml 1.0ml Final Syringe Reading 0.88ml 0.84ml 0.85ml Volume of EDTA Consumed 0.12ml 0.16ml 0.15ml Water Hardness ppm CaCO3 Average ppm
Which statements are TRUE regarding internal standards? I. The response factor is calculated by using a mixture containing known amounts of analyte and internal standard and by using detector response to the analyte and the internal standard. II. Internal standards are useful where instrument response or quantity of sample analyzed varies over time. III. Detector response is inversely proportional to concentration. IV. Detector response to analyte and internal standard is assumed to be constant over a range of concentrations A. I, II, and III B. II, III, and IV C. I and II D. I, II, and IV
please help this is my 4th time posting this and i havent gotten a correct answer. Please actually draw the graph out. A newly discovered enzyme, MBCase, cleaves carbon-carbon bonds of vicinal alcohol; The kinetic parameters were measured for 1.0 nM Of MBGase and determined to be a Km = 10 nM and a kcat = 100 s-1 a.) Sketch the graph out as a double-reciprocal plot (Lineweaver-Burke Plot) and label: -the axes (with units) -the point on the curve that can be used to determine Km -the point on the curve that can be used to determine Vmax
prepare an assignment on Application of HPLC in Drug Analysis(Amiloride): one page show name of the drug, dosage form, extraction step, type of column, separation parameters e.g., flow rate, mobile phase, detection wavelength and run time
A fly ash aerosol of monodisperse particles with a density of 2.0 g/mL and particle diameter of 10.0 mm has a concentration of 1000.0 mg/m3. Calculate the settling velocity in cm/s and the settling rate in g/m2-s. Please answer very soon will give rating surely
3. a. Briefly explain why internal standardization method is useful inanalytical chemistry?b. Why does a response factor of an instrument’s detector need to becalculated?
Answer the question and explain why you chose it in 3 sentences. Which statements are TRUE regarding internal standards? I. The response factor is calculated by using a mixture containing known amounts of analyte and internal standard and by using detector response to the analyte and the internal standard. II. Internal standards are useful where instrument response or quantity of sample analyzed varies over time. III. Detector response is inversely proportional to concentration. IV. Detector response to analyte and internal standard is assumed to be constant over a range of concentrations. Choices: A. I, II, and III B. II, III, and IV C. I and II. D. I, II, and IV
If some of the analytes were found to be out of range after doing the Quality Control and the machine repeatedly gives invalid result. What are the possible problem and best solution as a Medical Technologist?
Chemistry Column 25 m length and 0.2 mm I.D. has efficiency is 100,000 theoretical plates; Flow rate is 1 mL/min. Calculate the peak width for component with retention factor 2. Which data acquisition sampling rate should be used for proper quantification of this component? Explain. (For accurate integration peak should have at least
The following experimental data were collected during a study of the catalytic activity of an intestinalpeptidase with the substrate glycylglycine: Glycylglycine + H2O → 2 glycine [S] (mM) Rate of product formation (mol/min) 1.5 0.21 2.0 0.24 3.0 0.28 4.0 0.33 8.0 0.40 16.0 0.45 Use the graphical analysis (Lineweaver-Burk plot and equation) to determine the Km and Vmax for this enzyme preparation and substrate.
A direct reading instrument for mercury vapour analysis indicates a concentration of 0.01 ppm. If you want to do an impinger sampling for mercury vapour, what should be in minimum sampling period given that the analytical instrument has a detection limit of 100 ppb (0.1 ppm)? The impinger volume will be 20 mL and a sampling rate 1.5 L/min will be used. Assume NTP. (MW of Hg = 200.59)

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Instrumental Analysis

Chemistry

ISBN:

9781305577213

Author:

Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:

Cengage Learning

Fundamentals Of Analytical Chemistry

Chemistry

ISBN:

9781285640686

Author:

Skoog

Publisher:

Cengage

Appl Of Ms Excel In Analytical Chemistry

Chemistry

ISBN:

9781285686691

Author:

Crouch

Publisher:

Cengage

Principles of Instrumental Analysis

Chemistry

ISBN:

9781305577213

Author:

Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:

Cengage Learning

Fundamentals Of Analytical Chemistry

Chemistry

ISBN:

9781285640686

Author:

Skoog

Publisher:

Cengage

Appl Of Ms Excel In Analytical Chemistry

Chemistry

ISBN:

9781285686691

Author:

Crouch

Publisher:

Cengage

SEE MORE TEXTBOOKS