L 02. Round off your answer into a D5 For the figure shown, determine the elevation at C. Use Darcy-Weisbach formula to compute for the headloss in the pipes: hf, = 0.0826f whole number. Answer: Elev C = El 50m El 44m Q2 D1 = 1200 mm L, = 1800 m D, = 750 mm L, = 1350 m El C D, = 750 mm La = 1350 m Use f=0.02 for all pipes. Discharge in pipe 1, Q1 = 1.35m³/s

L 02. Round off your answer into a D5 For the figure shown, determine the elevation at C. Use Darcy-Weisbach formula to compute for the headloss in the pipes: hf, = 0.0826f whole number. Answer: Elev C = El 50m El 44m Q2 D1 = 1200 mm L, = 1800 m D, = 750 mm L, = 1350 m El C D, = 750 mm La = 1350 m Use f=0.02 for all pipes. Discharge in pipe 1, Q1 = 1.35m³/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Refer to Fig. P5.4. Water at 10°C flows up AB (5 m long, 40 mm diameter),then along BC (3 m long, 30 mm diameter). The measured pressure at A is 275kPa. (a) Find the pressure at C if the flow rate is 2.0 L/s. Neglect pipe frictionand energy losses. 6) Repeat for the same flow rate in the opposite direction.Table A.1 for water at 10°C: y = 9.804 kN/m².Vertical
1. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. a.) 39.5136 b.) 12. 9517 c.) 99.9358 d.) 30. 4889 2. What gage pressure p1 in kPa, is needed to provide the given flow rate? a.) 1121kPa b.) 1328kPa c.) 1692kPa d.) 1725kPa
A new cast iron pipe must carry 1.2 m3/2 at a head loss of 5m per km length of the pipe. Compute the diameter of the pipe in mm using n= 0.019 Choices: A. 1210.47 B. 1012.74 C. 2101.74 D.112.47 Please help. Show complete solution and avoid truncation. Thank you
If F=80 N, determine the magnitude and coordinate diretion angles of the couple moment. The pipe assembly lies in the x-y plane.
Water flows from a large reservoir at the rate of 0.0137 m3/s through the system shown in the Fig. below. Calculate the pressure at B. NB: Use f = 0.017 (friction factor) and fT = 0.010 in zone of complete turbulence. Hint: Include minor losses, assume K = 1.0 for the inlet or entrance and use the applicable appendix at the back of the textbook to obtain the pipe parameters.
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. A. 12.9517 B. 39.5136 C. 99.9358 D. 30.4889 What gage pressure p1 in kPa, is needed to provide the given flow rate? A. 1121 kPa B. 1725 kPa C. 1692 kPa D. 1328 kPa
A new cast iron pipe must carry 1.2 m3/2 at a head loss of 5m per km length of the pipe. Compute the diameter of the pipe in mm using f = 0.02 Choices: A. 681.95 B. 168.59 C. 961.85 D. 861. 95
Consider the simple pipe network below. Pipe AB and CF are both 500m long withdiameters of 0.8m and friction factors of 0.015. Branch 1 is 200m long, 0.5m in diameter with a frictionfactor of 0.02. Branch 2 is 300m long, 0.6m in diameter with a friction factor of 0.012. The designdischarge through pipe AB is 3m 3 /s. Determine the following: a) the equivalent pipe length, Leq, of asingle equivalent pipe with a diameter of 1m and friction factor of 0.02, that represents the entire pipenetwork from A to F, b) determine the total head loss from A to F. Ignore minor losses. (Hint: need touse method of equivalent pipes for both series and parallel)
A 12” pipe contains a short section in which the diameter is gradually reduced to 6” and then enlarged again to 12”. The 6” section is 2 ft below Section A in the 12” where the pressure is 75 psi. If a differential gage containing mercury is attached to the 12” and 6” sections, what is the deflection of the gage when the flow of water is 4.25 cfs downward? Draw the figure
Q2. A 200 mm x 100 mm venturimeter is provided in a vertical pipeline carrying oil of S = 0.9. The flow is in the upward direction. The throat is above the inlet by 0.25 and the differential manometer shows a gauge deflection of 0.25 m of Hg. Determine,(a) Discharge of oil (b) The pressure difference in N/m”2 between entrance and throat by using basic Bernoulli's equation. Take Cd = 0.98*
A sharp-edged orifice 75mm in diameter is installed at the bottom side at A as shown in thefigure below. If the coefficient of contraction Cc = 0.65 and the head loss is 700mm, compute thefollowinga. actual velocityb. coefficient of velocityc. actual discharge
A pipe carrying oil of sp gr 0 877 changes in A pipe carrying oil of sp gr 0.877 changes in size from 150mm at section E to 450mm at section R Section E is 3 66m lower than R section R. Section E is 3.66m lower than R and the pressures are 91.0kPa and 60.3kPa, respectively. If the discharge is 0.146m3 respectively. If the discharge is 0.146m /s, determine the lost head and the direction of flow.