L 1. What do you call the property of the object to resist any change in its rotational state of motion? A. Moment of Inertia B. Single Object C. Multiple Object System D. Rotational Motion 2. It is the rotational equivalent of force which means to twist: A. Inertia B. Torque C. Balance Force D. Unbalance Force 3. In the concept of torque, r symbols represents: A. The torque B. The force acting on the object C. The objects lever arm or moment arm D. The torque and the force acting on the object

L 1. What do you call the property of the object to resist any change in its rotational state of motion? A. Moment of Inertia B. Single Object C. Multiple Object System D. Rotational Motion 2. It is the rotational equivalent of force which means to twist: A. Inertia B. Torque C. Balance Force D. Unbalance Force 3. In the concept of torque, r symbols represents: A. The torque B. The force acting on the object C. The objects lever arm or moment arm D. The torque and the force acting on the object

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter10: Rotational Motion And Angular Momentum

Section: Chapter Questions

Problem 1CQ: Analogies exist between rotational and translational physical quantities. Identity the rotational...

See similar textbooks

Similar questions

Unreasonable Results A gymnast doing a forward flip lands on the mat and exerts a 500- Nm torque to slow and then reverse her angular velocity. Her initial angular velocity is 10.0 rad/s, and her moment of inertia is 0.050kgm2. (a) What time is required for her to exactly reverse her spin? (b) What is unreasonable about the result? (c) Which premises are unreasonable or inconsistent?
A cylinder with moment of inertia I1 rotates with angular velocity 0 about a frictionless vertical axle. A second cylinder, with moment of inertia I2, initially not. rotating, drops onto the first cylinder (Fig. P8.73). Because the surfaces are rough, the two cylinders eventually reach the same angular speed . (a) Calculate . (b) Show that kinetic energy is lost in this situation, and calculate the ratio of the final lo the initial kinetic energy. Figure P8.73
While punting a football, a kicker rotates his leg about the hip joint. The moment of inertia of the leg is 3.75kgm2 and its rotational kinetic energy is 175 J. (a) What is the angular velocity of the leg? (b) What is the velocity of tip of the punter’s shoe if it is 1.05 m from the hip joint?
Integrated Concepts An ultracentrifuge accelerates from rest to 100,000 rpm in 2.00 min. (a) What is its angular acceleration in rad/s2? (b) What is the tangential acceleration of a point 9.50 cm from the axis of rotation? (c) What is the radial acceleration in m/s2 and multiples of g of this point at full rpm?
A boy stands at the center of a platform that is rotating without friction at 1.0 rev/s. The boy holds weights as far from his body as possible. At this position the total moment of inertia of the boy, platform, and weights is 5.0kgm2 . The boy draws the weights in close to his body, thereby decreasing the total moment of inertia to 1.5kgm2 . (a) What Is the final angular velocity of the platform? (b) By how much does the rotational kinetic energy increase?
The moment of inertia of a long rod spun around an axis through one end perpendicular to its length is ML2/3 Why is this moment of inertia greater than it would be if you spun a point mass M at the location of the center of mass of the rod (at L/2)? (That would be ML2/4.)
Analogies exist between rotational and translational physical quantities. Identity the rotational term analogous to each of the following: acceleration, force, mass, work, translational kinetic energy, "near momentum, Impulse.
A bar on a hinge starts from rest and rotates with an angular acceleration = 10 + 6t, where is in rad/s2 and t is in seconds. Determine the angle in radians through which the bar turns in the first 4.00 s.
During a very quick stop, a car decelerates at 7.00 m/s2. (a) What is the angular acceleration of its 0.280-m-radius tires, assuming they do not slip on the pavement? (b) How many revolutions do the tires make before coming to rest, given their initial angular velocity is 95.0 rad/s? (c) How long does the car take to stop completely? (d) What distance does the car travel in this time? (e) What was the car's initial velocity? (f) Do the values obtained seem reasonable, considering that this stop happens very quickly?
A large grinding wheel in the shape of a solid cylinder of radius 0.330 m is free to rotate on a friction less, vertical axle. A constant tangential force of 250. N applied to its edge causes the wheel to have an angular acceleration of 0.940 rad/s2. (a) What is the moment of inertia of the wheel? (b) What is the mass of the wheel? (c) If the wheel starts from rest, what is its angular velocity after 5.00 s have elapsed, assuming the force is acting during that time?
Four objectsa hoop, a solid cylinder, a solid sphere, and a thin, spherical shelleach have a mass of 4.80 kg and a radius of 0.230 m. (a) Find the moment of inertia for each object as it rotates about the axes shown in Table 8.1. (b) Suppose each object is rolled down a ramp. Rank the translational speed of each object from highest to lowest, (c) Rank the objects rotational kinetic energies from highest to lowest as the objects roll down the ramp.
Consider the 12.0 kg motorcycle wheel shown in Figure 10.38. Assume it to be approximately an annular ring with an inner radius of 0.280 m and an outer radius of 0.330 m. The motorcycle is on its center stand, so that the wheel can spin freely. (a) If the drive chain exerts a force of 2200 N at a radius of 5.00 cm, what is the angular acceleration of the wheel? (b) What is the tangential acceleration of a point on the outer edge of the tire? (c) How long, starting from rest, does it take to reach an angular velocity of 80.0 rad/s? Figure 10.38 A motorcycle wheel has a moment of inertia approximately