Lab. 7 1. ___medium and _____reagent are used to detect indole production. _____will react with iron salt in SIM medium to form a black precipitate. _____bacteria will grow in a dense, well-defined line along the stab line. 4. What materials will be used in MRVP test? 5. Citrate positive will be indicated by ___color of the medium? TSIA medium contains three sugars___, ___, an iron salt, and ___.

Lab. 7 1. _medium and _reagent are used to detect indole production. _will react with iron salt in SIM medium to form a black precipitate. _bacteria will grow in a dense, well-defined line along the stab line. 4. What materials will be used in MRVP test? 5. Citrate positive will be indicated by _color of the medium? TSIA medium contains three sugars_, _, an iron salt, and ___.

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter33: Automated Methods Of Analysis

Section: Chapter Questions

Problem 33.5QAP: Give the advantages and disadvantages of sequential injection analyzers compared to traditional flow...

See similar textbooks

Similar questions

31 and 32. pls help and show solution plsss
Which statement is valid when the multiple extraction and single extraction is compared. The effciency of multiple extraction and single extraction is incomparable. Single extraction and multiple extraction have the same effciency Multiple extraction is more efficent than single extraction Single extraction is more efficient than multiple extraction
You finish doing an experiemnt with Benzoin. These are the results you get:Boiling start point: 137 ceciusBoiling end point: 140 ceciusVile while empty (with cap on): 15.348Vile with crude prod (with cap on: 15.748 Your starting weight: 1.00115.748 - 15.348 = 0.400 / 1.001 = 0.3996 or 39.96% YieldAnswer the following questions with this information:Initial Mass of impure sample:Mass of recrystallized benzoin:Percent reccovery of Benzoin:Melting pot range of purified benzoin:Literature melting point for benzoin:
How many milliliters of 0.050 0 M EDTA are required to react with 50.0 mL of (a) 0.010 0 M Ca21 or (b) 0.010 0 M Al31?
Why is splitless injection used with purge and trap sample preparation?
For each measurement in this list indicate whether it must be made precisely (P) or approximately (A). Mass of EDTA Final Volume of EDTA solution Volume placed in polyethylene bottle Final volume of unknown solution Volume of HCl used to make 0.6 M solution Volume of methyl red used Volume of sample titrated Volume of EDTA used to reach end point Volume of polyvinyl alcohol used
In a well plate dissolve benzophenone and benzioc acid in a small amount of ethyl acetate. Then use a capillary tube to spot sample onto pencil line. Add to developing chamber 1.5 mL Hexens, 3.5 mL ethyl acetate. Use UV lamp and circle spot.
Very pure silver nitrate standard reagent requires standardization with primary standard NaCl or KCl True False A water sample was analyzed for the total hardness through the reaction between the sample and EDTA. The data obtained from the experiment are presented below (MM CaCO3 = 100.0869 g/mol): Table 1. Standrdization of the EDTA solution mass of CaCO3 used 0.5467 g Initial burette reading 8.25 mL Final burette reading 16.65 mL Volume consumed 8.40 mL Table 2. Determination of Hardness of Water Volume of water sample 25.00 mL Initial burette reading 15.00 mL Final burette reading 24.00 mL Volume consumed 9.00 mL 23,469 ppm 22,456 ppm 21,290 ppm 23,990 ppm
Nitrous Acid Test Procedure: Make a solution of 4 grams NaNO3 in 16 mL water. Put 2 mL of concentrated hydrochloric acid into a 10x75-mm test tube and add 0.5 ml of amine. Cool the solution in a water-ice slush to zero degrees celcius. Add the nitrile solution slowly, dropwise, until a drop of the reaction mixture gives a blue spot on starch-iodide paper. The following should be tested: (NOTE: Include the observations and reaction equation) A. PRIMARY ALIPHATIC AMINES (Like Butylamine of Cyclohexylamine) B. PRIMARY AROMATIC AMINES I. Aniline + nitrous acid; then heat. II. Aniline + nitrous acid; then B-Napthol.
Full solution pls
What should you do if there are insoluble impurities after heating up your sample in the recrystallization solvent? a. Add more solvent to dissolves the impurities. b. Gravity filter the hot solution. c. Pick out the insoluble particles with a spatula. d. none of the above.
Materials and detailed methods: paragraph or two explain how the experiment was done Raw Data: Weight of paper weighed -1.834 1 gram of Anthracene= +1.007 0.5 grams of maleic Anhydride= +0.506 Heating bath at 140 C 10 ml of o-xylene added to 1 gram of Anthracene= +1.007 0.5 grams of maleic Anhydride= +0.506 Then place on heating bath at 140 C After heating reagents dissolve Then color changed from yellow to white clear Then mix is cooled in ice bath after a solid product is in the liquid solution You place that in vacuum filtration Product is off white crystal Crude product= +1.428 g