Logic XOR operation of (11101010)2 & (10101010)2 has a result of"? Explain your answer. A page fault means that we referenced a page A. Outside the memory boundaries B. With an incorrect I/O request C. That was not in secondary storage D. That was not in main memory Justify your answer with explanations

Logic XOR operation of (11101010)2 & (10101010)2 has a result of"? Explain your answer. A page fault means that we referenced a page A. Outside the memory boundaries B. With an incorrect I/O request C. That was not in secondary storage D. That was not in main memory Justify your answer with explanations

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter12: Secondary Storage Management

Section: Chapter Questions

Problem 12VE

See similar textbooks

Similar questions

8. The method which offers higher speeds of I/O transfers is a. Interrupts b. Memory mapping c. Program-controlled I/O d. DMA
Question 777 electric Program FSM Adder in Verilog (Datapath and controller) have to program that has work like below funtion. (with meely of moore machine) C<=A+B(1 ≤A ≤3) C<=A-B(4 ≤A ≤6) C<=A+2B(A == 7) C<=A-2B(A ≤ 0) Full explain this question and text typing work only thanks
One of these methods will produce less latency of I/O transfers is ___________ a.Program-controlled I/O b.DMA c.Interrupt driven I/O d.Memory mapping
Suppose that we have an atomic test-and-set-lock instruction that atomically copies val to old_val, and sets val to 1. void test_and_set(int* old_val, int* val); Write the implementations for the following functions of a Spinlock. void acquire(int* lock) { // your code } void release(int* lock) { // your code } PROVIDE CODE IN C
Question: Show the execution of each line of the given MIPS Code for $s0 = 0xA starting from“Main” till the code reaches “End”.Main: ble $s0, $0, Endsub $a0, $s0, $0Jal FuncJ EndFunc: add $v0, $0, $0Loop: addi $v0, $v0, 1srl $a0, $a0, 1bgt $a0, $0, LoopRet: jr $raEnd:
It is given that on a system, on average, an instruction executes in 1 nano second. Suppose that it takes 20 micro seconds of processor time for page fault. While, it takes 300 micro seconds of disk time for reading and writing a single page. Suppose that on average 1/3 of the pages that need to be paged out are modified. What is the average number of instructions between page faults that would cause the disk to be busy doing page transfers all the time?
Suppose the Vole communicates with a printer using the technique of memory-mapped I/O. Suppose also thataddress 0xFF is used to send characters to the printer, and address 0xFE is used to receive information about theprinter’s status. In particular, suppose the least significant bit at the address 0xFE indicates whether the printeris ready to receive another character (with a 0 indicating “not ready” and a 1 indicating “ready”). Starting ataddress 0x00, write a machine language routine that waits until the printer is ready for another character and thensends the character represented by the bit pattern in register 0x5 to the printer.
Consider the following scenario:a main program starts execution at time t = 03 second later device B sends interrupt signal5 second later device A sends interrupt signal2 second later device E sends interrupt signal3 second later device C sends interrupt signal5 second later device D sends interrupt signal5 second later device F sends interrupt signalhighlight on the following figure the paths of execution that realize the mentioned interrupt scenario.With each highlighted path indicate time value (t = ?)Finally draw one more path from the last ISR executed back to the main program and displayreturn time.
Consider a paging system with the page table stored in memory.a. If a memory reference takes 400 nanoseconds, how long does a paged memoryreference take?b. If we add TLBs, and 95 percent of all page-table references are found in the TLBs,what is the effective memory reference time? (Assume that finding a page-table entry inthe TLBs takes zero time, if the entry is there.)
What are the contents of the 25 memory bytes starting at address A, in hex, on a machine that uses Little Endian? (Hint: “a”=061h) Consider the following .data segment: A dw 0AAFFh B db 051h, 0CCh, 0EEh C times 3 dw -23 D dd -177 E db "e", -5, "c", 0 F times 2 dw -17 G dw 0EEh
When a CPU sends an interrupt, it is obliged to halt whatever it is doing in order to respond to the signal. I'm interested about the reasoning of halting the procedure in order to finish the assignment. Let's start with the process of interrupting, and then we'll go on to the process of executing. explain?
write the following questions a) Write an 8051 C program to send Hex values for ASCII characters of 0,1,2,3,4,5AB,C and D to port P1 b) Interface a 4X4 keyboard with 8086 using 8255, and write an ALP for detecting a key closure and return the key code in AL. The debouncing period for a key in 20 ms