Mass of evacuated syringe assembly: 36.9758g Mass of syringe assembly with Dust-Off spray: 37.1017g Mass of Dust-Off spray: 0.1259g Volume of water in syringe: 51mL Volume of Dust-Off spray (should be same as water): 51mL Air temperature: 23.3*C Atmospheric pressure: 729.0 atm Number of moles of Dust-Off spray based on the above P,V, and T: Experimentally determined molar mass of Dust-Off spray:

Mass of evacuated syringe assembly: 36.9758g Mass of syringe assembly with Dust-Off spray: 37.1017g Mass of Dust-Off spray: 0.1259g Volume of water in syringe: 51mL Volume of Dust-Off spray (should be same as water): 51mL Air temperature: 23.3*C Atmospheric pressure: 729.0 atm Number of moles of Dust-Off spray based on the above P,V, and T: Experimentally determined molar mass of Dust-Off spray:

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter12: Thermodynamic Processes And Thermochemistry

Section: Chapter Questions

Problem 79AP

See similar textbooks

Similar questions

When you determined the MW of a volatile liiquiid using the Erlenmeyer flask with the aluminum foil cap & the pinhole, explain briefly how you were able to obtain: -Mass of the vapor - Volume of the vapor -Pressure of the vapor - temperature of the vapor B) Calculate the MW of iodethane, a volatile liquid, given the following data obtained from the experiment in 12A, given that PV=nRT (R= 0.0821 L.atm.mol-1.K-1) Mass of residual liquid = 1.6384 g Pressure = 745.6 torr Volume of vapor = 327.8 mL Temp. of vapor = 100.0 C
Two industries (A and B) with the same process emit 250 µg/m3 of a certain compound at a gas temperature of 58oC. Taking into account that company (A) is located in a region whose average temperatures are 10oC higher than in the region where industry is located (B), it is expected that in the environment, (taking only the temperature effect) the compound concentration after emission is. ( ) can't say ( ) the same for both industries as they emit at the same temperature ( ) lower for industry A than for industry B ( ) higher for industry A than for industry B
6. As shown in Figure, a gas within a piston-cylinder assembly undergoes a thermodynamic cycle consisting of three processes in series: Process 1-2: Compression with U 2 =U 1 . Process 2-3: Constant-volume cooling to p 3 =140 kPa,; V 3 =0.028 m^ 2 . Process 3 - 1 : Constant-pressure expansion with W 31 =10.5 kJ. For the cycle, W eycle =28.3 kJ . There are no changes in kinetic or potential energy. Determine (a) the volume at state 1, in m ^ 3 . (b) the work and heat transfer for process 1-2, each in kJ. (e) Can this be a power cycle? A refrigeration cycle? Explain.
What Is The Ideal-Gas Equation of State?
A rigid insulated tank is divided into 2 equal compartments by athin rigid partition. One of the compartments contains air, assumedto be an ideal gas at 800 kPa and 250◦C. The other compartment isunder a vacuum. The partition is suddenly broken and the air rushesinto the evacuated compartment. The tank pressure and temperatureeventually equilibrate. (a) what is the final temperature of the gas ◦C?(b) what is the final pressure, kPa?(c) how much work is done by the system, kJ/kg?(d) how much heat is transferred to the system kJ/kg
A mixture of 1 kmol of gaseous methane and 2 kmol of oxygen initially at 258C and 1 atm burns completelyin a closed, rigid container. Heat transfer occurs until the products are cooled to 900 K. If the reactants andproducts each form ideal gas mixtures, determine (a) the amount of heat transfer, in kJ, and (b) the finalpressure, in atm.
A fuel has the following volumetric analysis: CH4 = 68% C2H6 = 32% Assume complete combustion with 15% excess aur at 101.325 kPa and 27 degrees dry bulb temperature. What is the total moles in the products of combustion?
Calculate the GCV and the balance equation on the combustion of ethane (C2H6) assuming complete combustion at 25 degree Celsius. __ C2H6 + ___ O2 --> __ CO2 + __H2O delta Hf of C2H6 = -83.75 kJ/mole delta Hf of liquid water = -285.82 kJ/mole delta Hf of water vapor = -241. 82 kJ/mole delta Hf of carbon dioxide = -393.5 kJ/mole
Calculate the ΔHsoln and ΔSsoln for the dissolution of solid KHP from the trendline equation of your scatter graph. Include units. Reffer to equation 4. R is the gas constant 8.314J mol-1 K-1 The trendline equation -5623*x + 17.7 Equation 4 Ln Ksp = - ΔHsoln/R (1/T) + ΔSsoln/ R
A hot-air balloon achieves its buoyant lift by heating the airinside the balloon, which makes it less dense than the air outside.Suppose the volume of a balloon is 1800 m3 and therequired lift is 2700 N (rough estimate of the weight of theequiptment and passenger). Calculate the temperature of the airinside the balloon which will produce the required lift. Assumethat the outside air temperature is 0 degrees C and that the air isan ideal gas under these conditions.How do I go about applying the ideal gas law to a problem like thiswhich asks me to factor in buoyant lift?Thanks!
Suppose that 3.0 mmol N2(g) occupies 36 cm3 at 300 K and expands to 60 cm3. Calculate dG for the process.
The piston-cylinder below is depicted before and after a gaseous reaction that is carried out in it at constant pres sure: the temperature is 150 K before and 300 K after the reaction. (Assume the cylinder is insulated.)