Match the steel microstructures to their names А B C A [Choose ] [ Choose ] [ Choose ] > B.

Q: A hollow steel has an outside diameter of 5in. and it’s inside diameter is 4in. What is the…

A:

Q: give 8 examples of cold formed steel and state each of their uses or where can be seen or used

A: Cold-formed steel members are used additionally in bridges, storage racks, grain bins, car bodies,…

Q: Delermine the average normal stress in the aluminum due to this loading The A-36 steel pipe in…

A: Determine stress in steel and aluminium

Q: What change in volume would a 100 mm cube of steel suffer at a depth of 5 km in sea water? Take…

A:

Q: An aluminum tube is fastened between a steel rod and a bronze rod as shown. Axial loads are applied…

A: Draw the free body diagram of the three tubes as below. Determine the load P from the overall…

Q: A column splice is used to increase

A: Column splicing is done to achieved the desired length on site . Column splicing is made because…

Q: A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are ex = 0.40…

A: Given data in question  Axis system  Strains in x and y directions  Poissons ratio Elasticity…

Q: 2. The materials that have low values of tensile strain * concrete steel Aluminum Brass O All above…

A: Material that has low value of strain rate

Q: Why does the iron–carbon phase diagram go only to 6.7% carbon?

A: The iron-carbon phase diagram is shown below,

Q: A tensile stress is to be applied along the axis of a cylindrical brass rod that has a diameter of…

A:

Q: The shape of the grain are based on the followings categories EXCEPT: (a) bulky (b) flaky (c)…

A: The shape of soil grains can be : Flaky Needle shaped Bulky

Q: A tensile load of 150kN is applied to a round metal bar with a diameter of 16mm and a gage length of…

A: Find a.) Modulus of elasticity (MPa)b.) Poisson's ratio for this metal

Q: Find the axial stress (in psi) of the steel. " Your answer Find the axial stress (in psi) of the…

A:

Q: Unit for strain is 2 O a. N/mm 3 O b. mm O c. mm O d. No unit

A: Finding out unit of strain.

Q: A) A specimen of alloy having the following engineering stresses produces the corresponding plastic…

A: Given above table and we have to find the engineering stress which produces engineering strain of…

Q: 5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in the given figure.…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: Situation 5: The compound shaft as shown is attached to rigid supports. It is subjected to a…

A:

Q: nd the cross-sectional area of steel bar that will not deform e than 10mm nor be stressed b 100 Mpa…

A:

Q: : Prtal methed

A:

Q: The component along the a-axis is pounds (lbs).

A: given- a force applied at an angle of 60 degree with a-axis. angle which the force makes with b-axis…

Q: PROBLEM 4: As shown in the diagram shown, there is a gap of 0.5 mm between the rods at 10°C.…

A:

Q: A steel has a BHN = 300. What is its approximate ultimate strength in ksi?

A: Given: Brinell hardeness number  To find:  Ultimate strength

Q: Axial loads are applied to the compound ro composed of an aluminum segment rigidly connected between…

A:

Q: The design tensile strength The allowable tensile strength

A:

Q: It is a structure used by structural engineers to perform simple force analysis and is effective in…

A: Option 1 is correct  Influence line

Q: What is high-performance steel? State two HPS products that are currentlybeing used in structural…

A: Introduction : High performance steel : High Performance Steel (HPS) is a classification given to…

Q: Q-1) a) What is the difference between elasticity and plasticity.   b ) what is the difference…

A: Answer  Difference between elasticity and plasticity as follows

Q: 21)A hardness test confused on a particular grade of steel gives a Brinell Hardnes Number (HB) of…

A: Since, the question number to be solved is not specified, the solution for Question 21, 22 and 23 is…

Q: 8. If the modular ratio is equal to 11, and the Modulus of Elasticity of the Steel is 200,000 MPa.…

A: GIVEN Modular ratio, m = 11 Modulus of elasticity of steel, Es = 200,000 MPa To Determine Value of…

Q: As shown in the figure below, a bronze bar is affixed between a steel bar and an aluminum bar. Axial…

A: Given, Allowable stress :- σst = 150MPa σbr= 130MPa σal = 90MPa Est= 200Gpa Eal= 70Gpa Ebr= 83Gpa

Q: A combined section of steel and copper is subjected to a compressive load. Refer to the table below…

A: Assume that 100 kN load is applied. Then using equilibrium and compatibility equation the load…

Q: 5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in the given figure.…

A: Steel section -  P = σstAst⇒P = 120×480⇒P =57600 N   Bronze section -  Pbr = σbrAbr⇒2P = 90×650⇒2P…

Q: Two uniform spheres are positioned as shown. Determine the gravitational force F which the titanium…

A:

Q: A combined section of steel and copper is subjected to a compressive load. Refer to the table below…

A: We will calculate stress using maximum strain.

Q: Design rod to support load of 175,000 pounds. What diameter rod is appropriate?   Safety Factor,…

A:

Q: e strength o pre stressing tendons ess after losses

A: solution data given fc' =34.5 MPa Ec= 4700×fc'Ec =4700×34.5  =27606.25 N/mm2→ for graded 270 , Es…

Q: What do you mean by Corrosion of Steel

A: The process of degradation of material by reactions chemically, electrochemically with environment…

Q: To get adequate strength and ductility for mild steel, up to What percentage of corbon content is…

A: Ductility is the ability of a material to sustain under tensile loads and to have plastic…

Q: 5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in Figure 5. Axial…

A: Given data

Q: (a) Explain the phenomenon of strain hardening.

A: to find phenomenon of strain harding

Q: Determine the ductility of the following steel samples that undergo tensile strength test. All…

A:

Q: These are design tools except A. Geometric modelling B. High precision data c. Optimization methods…

A: Note- Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: One of the following values is a possible for possion ratio for steel ? a. Zero b. one c. 0.3 d…

A: given data : One of the following values is a possible for possion ratio for steel ? a. Zero b. one…