Material A (shown below) is experiencing forces shown below at different points along its body. If the area of its cross section is equal to 0.35 in^2, determine the total new length of the material if modulus of elasticity is equal to 5x10*6 psi. AB -4 ft BC -4.5 ft, CD - 3.5 ft. 6000 Ib 7000 Ib 5000 lb 4000 lb 12.0158 ft. O 12.0191 ft. O 120211 t. ary tion 12.0165 ft. O 120175 t rvev O 120285 ft IS 120231 ft

Material A (shown below) is experiencing forces shown below at different points along its body. If the area of its cross section is equal to 0.35 in^2, determine the total new length of the material if modulus of elasticity is equal to 5x10*6 psi. AB -4 ft BC -4.5 ft, CD - 3.5 ft. 6000 Ib 7000 Ib 5000 lb 4000 lb 12.0158 ft. O 12.0191 ft. O 120211 t. ary tion 12.0165 ft. O 120175 t rvev O 120285 ft IS 120231 ft

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter9: Mass And Mass-related Variables In Engineering

Section: Chapter Questions

Problem 4P

See similar textbooks

Similar questions

Need help experts. The rigid body shown in the figure is subjected to the indicated force system. Determine the forces applied at points A and E that equal the applied force system.Data: β = 48°; a = 6,6 m; b = 8,9 m; F = 31 kN; P1 = 20,743 kN; P2 = 23,037 kN The force applied at point A is FA = ? Answer kN and the force applied at point B is FB = ? Answer kN.
Q#4: A shaft having length equal to 10 m and diameter equal to (57) mm is simply supported at both ends. The shaft carries four masses (157) kg, (207) kg, (257) kg and (307) kg. These masses are located at a distance of 1.5 m, 2.5 m, 5.5 m and 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m2 and mass density for the shaft material is 7500 kg/m3. Determine critical speed of the shaft in revolutions per minute for the following two cases: Effect of the mass of the shaft is neglected. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
Q.2 Three bars each made of different materials are connected together and placed between two walls when the temperature is T1 = 12 oC. Determine the force exerted on the rigid supports when the temperature becomes T2=18 oC. The material properties and crosssectional area of each bar are given in the figure.
The bar shown determines: a) The internal force in section AB, BC and CD. b) The approach or distance between points B and C, and between points C and D. c) The displacement of points A, B, C and D. d) Conceptually, what is the difference between deformation and displacement? Consider: Cross-sectional area of the bar A=50 mm2 , Modulus of elasticity E = 200 x109Pa
Civil engineering question (Strength of material) - The 30 foot long cantilevered beam is depicted in the illustration. 6 inches thick and 2 feet deep. It is constructed of steel with a 15.2 slug/ft bulk density. At a 30 degree inclination to the vertical in the x-y plane, it can hold a 1000 lbf load. Between 250 °F at the support to 70 °F at its free end, the temperature of the beam changes linearly. Calculate its weight and mass, and convert the measurements to SI units.
As shown, a uniform beam of length d = 1.80m and mass 21.3kg is attached to a wall with a pin at point B. A cable attached at point A supports the beam. The beam supports a distributed weight W2 = 345N/m . If the support cable can sustain a maximum tension of 1250N , what is the maximum value for W1? Under this maximum weight, what is FBy which is the vertical component of the support's reaction force at point B? Show calculations. Will rate if correct.
As shown in the figure a rigid beam with a negligible mass is pinned at O and supported by 2 rods identical except for length. If P=30KN, find the load in rod A and B in KN. If rod A elongates by 2mm how much is the elongation of rod B in mm?
15. A measure of the resistance of a material to change of volume without change of shape or form a. Young’s modulus b. Modulus of rigidity c. Bulk modulus d. Shear modulus 16. Which support offers horizontal and vertical reaction a. roller support b. hinged support c. fixed support d. all of these 17. The beam whose one end remains fixed and the other end is supported by roller, called as a. simple supported beam b. cantilever beam c. propped beam d. overhanging beam
As seen in the figure, a rigid beam carried by three elastic rods of equal length from points A, B, and C is pulled to Eve from points F by P-force. The modulus of elasticity of the bars are E1=100GPa, E2=120GPa and E3=100GPa. Yield stress σA=40 MPa for bar 1 and 3, yield stress σA=120 MPa for bar number 2. Accordingly, a) determine the load PA that will start the flow, b) the load PG that will cause the migration.
15. Compute the resultant of the three forces shown in the figure. A. 894.32 N B. 836.90 N C. None of the Above D. 315.28 N E. 948.27 N
Two masses are attached to a uniform meter stick as shown in the figure below. Themasses of m1 and m2 are as given and the meter stick weighs 150 g. A force F withunknown magnitude is applied on one end of the stick at an angle of 30° to balancethe system. (a) What is the magnitude of F? (Ans: 6.21 N)(b) What are the reaction forces on the support? (Ans: Rx = 5.38 N; Ry = 5.80 N)
Problem 9. For the tank shown in the figure, the following dimensions apply: h1=3.00m h2=4.50m w=2.50m y=9.81kN/m^3. Compute the horizontal component of the resultant force on the curved surfaces.a. 168.0 kNb. 158.0 kNc. 148.0 kNd. 138.0 kNe. 128.0 kNf. 118.0 kN