Material A (shown below) is experiencing forces shown below at different points along its body. If the area of its cross section is equal to 0.35 in^2, determine the total new length of the material if modulus of elasticity is equal to 5x10^6 psi. AB =4 ft BC =4.5 ft, CD = 3.5 ft. Note: Final Answer in 4 decimal places.

Material A (shown below) is experiencing forces shown below at different points along its body. If the area of its cross section is equal to 0.35 in^2, determine the total new length of the material if modulus of elasticity is equal to 5x10^6 psi. AB =4 ft BC =4.5 ft, CD = 3.5 ft. Note: Final Answer in 4 decimal places.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.1P: A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel...

See similar textbooks

Similar questions

The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?
A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
A [0/90/0/±45]s Glass/Epoxy laminate is subjected to the following mechanical loads: Nx =Ny= 80*10^5 N/m. The thickness of each lamina is 0.25 mm. Longitudinal modulus of elasticity = E1 = 38.6 GPa , Transverse modulus of elasticity = E2 = 8.27 GPa , Poisons Ratio 0.26. a) Determine the local stresses at the top of 45° ply
See the set of bars for made of a material that has a yield strength of 350 MPa, determine the minimum h1 and h2 dimensions required. Apply a safety factor F.S. = 1.5 without flow. Each bar is 12 mm thick
A spherical tank contains an internal pressure of 3.0 MPa, the diameter is 16 m, the yield stress is 490 MPa. and the factor of safety is 2.5. Determine the required thickness I to the nearest millimeter.
K=17 so 107 MPa strength of material question.
If the shear modulus of a material is 120GPa & the bulk modulus is 140 GPa, then Young’s modulus is------ a. 820 GPa b. 280 Pa c. 280 GPa d. 820 Pa
An 18 coils helical spring having a load of 100kg. The modulus of elasticity in shear of spring is 96.62 GPa, OD of 9.256 cm and with wire diameter of 9.525 mm. The spring is squared and ground ends. Compute for the following respectively: 1) number of effective coils2) spring index3) axial load (N) 4) deflection (mm) Answers must be at least in 4 decimal places.