An aluminum fin [k = 200 W/m.°C] 3.0 mm thick and 7.5 cm long protrudes from a wall, as shown below. The base is maintained at 300°C, and the ambient temperature is 50°C with h = 10 W/m2.C. Calculate the heat loss from the fin per unit depth of material. [Hint: correct for the tip, i.e use L] %3D dq.h Pax (T-T

An aluminum fin [k = 200 W/m.°C] 3.0 mm thick and 7.5 cm long protrudes from a wall, as shown below. The base is maintained at 300°C, and the ambient temperature is 50°C with h = 10 W/m2.C. Calculate the heat loss from the fin per unit depth of material. [Hint: correct for the tip, i.e use L] %3D dq.h Pax (T-T

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.36P

See similar textbooks

Similar questions

After the sinking of RMS Titanic, US operated the International Ice patrol with the purpose of monitoring the presence and movements of icebergs in the Atlantic and Arctic oceans. Once, they observed a unique tabular iceberg in a form of a rectangle (250 km x 50 km x 300 m). How many years would it take to melt the iceberg solely by heat from the sun if the ice absorbs a mean of 98 J/m2 -s, 12.5 hrs per day? Note: the exposed area for heating is 250 km x 50 km and the density is 920 kg/m3 . This is my solution.
You are designing a small heatsink to cool a high-powered IC on a control unit PCB. The IC puts out 40,000 W/m2 and has a size of 40mm x 20mm. A fan blows 40 degrees C air across the IC at a speed of 4 m/s. The IC is well insulated on its back face. If the convection coefficient is 62 W/m2K, what is the surface temperature of the IC?
A gas vessel 1.5m x 1.5m x 2m containing Carbon Dioxide (CO2) with a temperature of -3°C. The right vessel wall is fixed to the wall, as shown in Figure Q1 (a). A minimum force of 10kN is required to split/open the gas vessel. Calculate: i. Vacuum pressure of CO2.ii. Mass of the CO2. Take molecular weight for Oxygen= 16, Carbon = 12, atmosphericpressure 100kPa, and universal gas constant = 8314 J⋅kmol−1⋅K−1
Find the minimum amount of diameter for the insulation of a spherical water tank? Radius of the tank is 10 m, thermal conductivity is 25 W/(m^2*K) and convective coefficient is 5 W/(m*K)
1. Most bridges contain interlocking steel grates (α steel = 1.2 x 10 - 5 ºC -1 ) that allow the bridge toexpand and contract with the changes in temperature. The Golden Gate Bridge in San Francisco isabout 1350 meters long.(A) The seasonal temperature variation in San Francisco ranges from about 0ºC to 30ºC. Howmuch will the bridge expand between these two extremes?(B) What percent of the length of a subcompact automobile, 2.5 meters, does this gaprepresent?2. Selena has a fire in her fireplace to warm her 20ºC apartment. She realizes that she hasaccidentally left the iron poker (α iron = 1.2 x 10 -5 ºC -1 ) in the fire. How hot is the fire if the 0.60-meter poker lengthens 0.30 cm?3. Just before midnight, when the air temperature of 10.0ºC, Karl stops and fills the 0.0600 m 3 gastank in his car. At noon the next day, when the temperature has risen to 32ºC, Karl finds a puddle ofgasoline (βgas = 3 x 10 -4 ºC -1 ) beneath his car.(A) How much gasoline spilled out of Karl's car?…
3.A steam at 118°C is flowing inside a diameter of 40 mm, thickness of 10 mm ceramic pipe (k=1.52 W/mK). The pipe is insulated with 25 mm of insulator (k=0.064 W/m K). The convective coefficient for steam inside the pipe is h;=20.7 W/m²K and the convective coefficient for air outside the pipe is h.=0.07W/m²K. The air is at a temperature of 28°C ? (1)Calculate the heat loss per unit length of 1m of pipe (W)? (2)Repeat, using the overall U; based on the inside area A; ?
A vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for heat-transfer purposes. Suppose the surface temperature of the cylinder is 78°F, h=2 Btu/h · ft2 . °F, the surface emissivity is 0.9, and the cylinder is placed in a large room where the air temperature is 68°F and the wall temperature is 45°F. Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you conclude from these calculations? Known, Find, Schematic Diagram, Assumption, Properties, Analysis and Comments
A vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for heat-transfer purposes. Suppose the surface temperature of the cylinder is 78°F, h=2 Btu/h · ft2 . °F, the surface emissivity is 0.9, and the cylinder is placed in a large room where the air temperature is 68°F and the wall temperature is 45°F. Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you conclude from these calculations?
Consider the vertical heat sink (see the figure) used to cool a surface at 70 0C. The room temperature is 30 0C. The dimensions are given as (H=2 cm, L=5 cm, t=1 mm, W=15 cm). If the space between the fins is arranged so that the heat transfer rate is maximum, what is the heat transfer rate from the heat sink? Properties of air: ρ=1 kg/m3, k=0.03 W/mK, ν=1.5x10-5 m2/s, cp=1 kJ/kg0C, Pr=0.7
A spacecraft radioisotope thermoelectric generator (RTG) contains a cylindrical nuclear element, pictured below. The nuclear element generates q̇g = 200 kW/m3. The RTG is surrounded by eight (N = 8) identical rectangular fins. Each fin’s height (H), length (L), and thickness (t) are given in the picture. The fins are directly machined from a stainless steel cladding of inner and outer radii r1 and r2, respectively. The stainless steel has thermal conductivity of k = 18 W/m·K. Assume that the RTG is in a well-ventilated lab, where the convection heat transfer coefficient is h = 20 W/m2·K and the surrounding temperature is T = 20°C. Ignore effects of thermal radiation. (a) Calculate the fin efficiency of a single rectangular fin, f. (b) Calculate the overall fin efficiency of the entire eight fin array, Obtain the maximum temperature in the stainless steel cladding, T(r1).
A steam pipe carrying steam at 380 kPa pressure for a distance of 120 m in a chemical plant is not insulated. Estimate the Amount of heat saved if 16 cm steam line were covered with 85% magnesia pipe covering 5 cm thick. Take room temperature to be 36 ℃. Thermal conductivity of 85% magnesia is 0.0745 W/m−K , unit convective coefficient of room air, ho = 12 W m2−K .Take the steam temperature as 142℃. Use atleast 4 decimal places in every computation
Estimate the thermal conductivity of Applesauce at 35 ° C. (Air content = 78.0% wet basis). Thermal conductivity of the material = Answer W / m ° C