Strain Stress (Мра) 0.002 220 STRESS VS. STRAIN 0.003 340 450 0.004 360 400 0.005 400 350 0.006 420 300 0.007 415 250 0.008 400 200 0.009 380 150 100 50 0.002 0.004 0.006 0.008 0.01 STRAIN 1)A) Estimate the Young's Elastic Modulus from the data and graph above. Watch units. B) Estimate the proportional limit of this material. C) Estimate the Yield Strength of this material. TENSILE STRESS (MPA)

Strain Stress (Мра) 0.002 220 STRESS VS. STRAIN 0.003 340 450 0.004 360 400 0.005 400 350 0.006 420 300 0.007 415 250 0.008 400 200 0.009 380 150 100 50 0.002 0.004 0.006 0.008 0.01 STRAIN 1)A) Estimate the Young's Elastic Modulus from the data and graph above. Watch units. B) Estimate the proportional limit of this material. C) Estimate the Yield Strength of this material. TENSILE STRESS (MPA)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.2P: 5.2 Evaluate the Prandtl number from the following data: , .

See similar textbooks

Similar questions

The length of a iron bar is measured by a number of different observers and the following set of 12measurements are recorded (units mm)302,304,303,305,307,309,310,311,312,301,303,302. Find the values of mean, median, variance andstandard deviation.
The elastic region of a materials stress strain graph is shown below. Determine the Modulus of Elasticity from the graph data then select the correct modulus in the choices below. 20,000,000 psi 30,000,000 psi 40,000,000 psi 5,000,000 psi
The materials laboratory that you direct received the following data on the tensile strength in MPa of 15 samples of Aluminum Nitride. The data obtained for each sample are: Sample Endurance (Mpa) SAMPLE (STRENGTH) MPa 1 190 2 233 3 268 4 160 5 257 6 300 7 310 8 262 9 185 10 205 11 275 12 245 13 220 14 290 15 228 You are asked to calculate the Weibull modulus, m, considering that the probability of failure is n/16, where n is the number of specimens that failed at a given stress. You can use Excel to speed up the calculations.
The nuchal ligament in a horse supports the weight of the horse’s head. This ligament is much more elastic than a typical ligament, stretching from 15% to 45% longer than its resting length as a horse’s head moves up and down while it runs. This stretch of the ligament stores energy, making locomotion more efficient. Measurements on a segment of ligament show a linear stress-versusstrain relationship until the stress approaches 0.80. Smoothed data for the stretch are shown. The volume of the ligament stays the same as it stretches, so the cross-section area decreases as the length increases. Given this, how would a force F versus change in length ΔL curve appear?
Five of your classmates measured the diagonal length of the blackboard. Classmate A measured it as 2.54 m; classmate B as 2.46 m; classmate C as 2.65 m; classmate D as 2.55 m; and classmate E as 2.39m. Find the variance and standard deviation of the measurements. Also, express the average measurement in a form that includes uncertainty.
The following table lists molecular weight data for a polypropylene material. Compute the number-average molecular weight, Molecular Weight Range (g/mol)//// xi////// wi 8,000–16,000//// 0.05/// 0.02 16,000–24,000 ///0.16// 0.10 24,000–32,000 ///0.24// 0.20 32,000–40,000 ///0.28// 0.30 40,000–48,000 ///0.20// 0.27 48,000–56,000 ///0.07// 0.11 Round your answer to 0 decimal places.
Mr. C studies the strength of the material used for a baseball bat, he knows that the strength is approximately normally distributed with a standard deviation of 175 psi. A random sample 30 specimens has a mean strength of 2,750 psi. a) What is the z-value when the mean strength is tested to be 3,000 psi, b) What will be the decision for the hypothesis testing with a=0.05 c) What is the minimum mean tensile strength needed from 30 samples, for the claim of 3,000 psi to be failed to rejected.
5.2 Evaluate the Prandtl number from the following data: , .
A company makes electrical resistors. The perfect resistor has a value of 400 ohms. A sample of 2000 resistors was tested and found to have a mean of 391.5 ohms and a standard deviation of 22.5 ohms. Assuming a normal distribution:a. How many resistors in the sample will have more than 440 ohms of resistance?b. How many resistors in the sample will have less than 360 ohms of resistance? note: you can use the frequency distribution table picture I attached.
1.The thickness of a gage block is measured five times using an instrument that has a resolution of 0.001 cm. The following measurements are obtained (in cm): 1.100, 1.110, 1.090, 1.095, and 1.105. The true gauge block thickness is known to be 1.050 cm. Use this information to answer the following questions: a. What errors or sources of measurement error can be identified in the example? (Hint: there are three). Identify each one as a random or systematic uncertainty. b. Estimate the magnitudes of each of these uncertainties. Wherever possible, estimate random uncertainties at a 95% probability/confidence level. c. Based on the uncertainties determined in part b, estimate the overall uncertainty of a measurement obtained by this instrument.
The standard deviation of linear dimensions P and Q are 3 um and 4 um respectively. When assembled, the standard deviation in um of the resulting linear dimension P+Q will be,
The following table lists molecular weight data for a polypropylene material. Compute the weight-average molecular weight, Molecular Weight Range (g/mol)//// xi////// wi 8,000–16,000//// 0.05/// 0.02 16,000–24,000 ///0.16// 0.10 24,000–32,000 ///0.24// 0.20 32,000–40,000 ///0.28// 0.30 40,000–48,000 ///0.20// 0.27 48,000–56,000 ///0.07// 0.11 Round your answer to 0 decimal places.