Arigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the polnt C to displace downward by 0.1 mm. Given: E (wire B) = 200 Gpa. E (wire C) = 70 Gpa and both wires have a diameter D 6 mm. Consider a linear elastic behavior. 2 m 1.5 m A 3 m 2 m 2 m CO

Arigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the polnt C to displace downward by 0.1 mm. Given: E (wire B) = 200 Gpa. E (wire C) = 70 Gpa and both wires have a diameter D 6 mm. Consider a linear elastic behavior. 2 m 1.5 m A 3 m 2 m 2 m CO

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.6.1P: A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned...

See similar textbooks

Similar questions

A prismatic bar in tension has a length L = 2.0 m and cross-sectional area A =249 mn2. The material of the bar has the stress-strain curve shown in the figure. Determi ne t he elongation 5 of the bar for each of the following axial loads: P = 10 kN, 20 kN, 30 kN, 40 kN. and 45 kN. From these results, plot a diagram of load P versus elongation 5 (load-displacement diagram).
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas. Calculate maximum permissible pressure in the balloon if the allowable normal strain at the outer surface of the balloon is O.h Assume E = 4 MPa and v = 0,45.
A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the point C to displace downward by 0.6 mm. Given: E (wire B) = 200 Gpa, E (wire C) = 70 Gpa and both wires have a diameter D = 2 mm. Consider a linear elastic behavior.
A rigid beam is supported by a pin at A and two metallic wires at Band C. Determine the force P that causes the point C to displace downward by 0.2 mm. Given: E (wire B) 70 Gpa, E (wire C) = 200 Gpa and both wires have a diameter D 5 mm. Consider a linear elastic behavior.
A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the point C to displace downward by 0.1 mm. Given: E (wire B) = 70 Gpa, E (wire C) = 200 Gpa and both wires have a diameter D = 6 mm. Consider a linear elastic behavior. Select one: P = 597 N P = 537 N P = 430 N P = 573 N P = 287 N
A bar having a length of 5 in. and a cross-sectional area of 0.7 in.2 is subjected to an axial force of 8000 lb. If the bar stretches 0.002 in., determine the modulus of elasticity of the material. The material has linear elastic behavior.
A [0/90/0/±45]s Glass/Epoxy laminate is subjected to the following mechanical loads: Nx =Ny= 80*10^5 N/m. The thickness of each lamina is 0.25 mm. Longitudinal modulus of elasticity = E1 = 38.6 GPa , Transverse modulus of elasticity = E2 = 8.27 GPa , Poisons Ratio 0.26. a) Determine the local stresses at the top of 45° ply
A solid circular rod that is 600 mm long and 20 mm in diameter is subjected to an axial force of P = 50 kN. The elongation of the rod is d = 1.40 mm, and its diameter becomes d = 19.9837 mm. Determine the modulus of elasticity and the modulus of rigidity of the material. Assume that the material does not yield.
Determine the change in the volume of a 10 cm diameter copper sphere that is subjected to a hydrostatic pressure of 120 MPa assuming linear elastic behavior up to this stress level. (V =4/3 n 13) (E: 125 GPa, v = 0.34, SY = 200 MPa)
Please help me for the correct solution. A leaf spring carries a central load of 3000 N. The leaf spring has to be made of 10 steel plates 5cm wide and 6mm thick. If the bending stress is limited to 150 N/mm² determine: (i) Length of the spring and (ii) Deflection at the centre of the spring. Take E = 2 * 10 ^ 5 * N / m * m ^ 2..?
A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the point C to displace downward by 0.6 mm. Given: E (wire B) = 200 Gpa, E (wire C) = 70 Gpa and both wires have a diameter D = 2 mm. Consider a linear elastic behavior. 2 m 1.5 m C 3 m 2 m 2 m Select one: O P= 235 N O P= 471 N O P= 314 N P= 294 N