A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the point C to displace downward by 0.1 mm. Given: E (wire B) = 70 Gpa, E (wire C) = 200 Gpa and both wires have a diameter D = 6 mm. Consider a linear elastic behavior. Select one: P = 597 N P = 537 N P = 430 N P = 573 N P = 287 N

A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the point C to displace downward by 0.1 mm. Given: E (wire B) = 70 Gpa, E (wire C) = 200 Gpa and both wires have a diameter D = 6 mm. Consider a linear elastic behavior. Select one: P = 597 N P = 537 N P = 430 N P = 573 N P = 287 N

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.8.1P: The shear stresses t in a rectangular beam arc given by Eq. (5-43): in which Fis the shear force, /...

See similar textbooks

Similar questions

A surveillance camera weighing 3 kg is mounted on a tubular frame as shown.shows in the following image. There is an external disturbance ?(?) = 30 cos(50?) ? actingabout the camera. Determine the cross section of the aluminum structure if it is the maximumamplitude is limited to 2 mm
The wires each have a diameter of 2 cm, length of 6 m, and aremade from a material with modulus of elasticity ? = 19.3 GPa.If three external loadings are applied to the rigid beam AC,determine the angle of tilt of the rigid beam. Assume thedeformation of the wires obeys the Hooke’s law
The brass tube AB (E = 105 GPa) has a cross-sectional areaof 138 mm² and is fitted with a plug at A. The tube is attached atB to a rigid plate that is itself attached at C to the bottom of analuminum cylinder (E = 70 GPa) with a cross-sectional areaof 250 mm². The cylinder is then hung from a support at D. In orderto close the cylinder, the plug must move down through 1.2 mm. Determine the force P that must be applied to the cylinder.
A hollow circular column of 200 mm external and 160 mm internal diameter is subject to anaxial compressive load of 150 kN with an eccentricity of 25 mm from the centroidal axis.The column is 5.0 m long and both ends fixed. Determine the maximum compressive stressand deflection in the column (assume E = 120 GPa).
Please help me for the correct solution. A leaf spring carries a central load of 3000 N. The leaf spring has to be made of 10 steel plates 5cm wide and 6mm thick. If the bending stress is limited to 150 N/mm² determine: (i) Length of the spring and (ii) Deflection at the centre of the spring. Take E = 2 * 10 ^ 5 * N / m * m ^ 2..?
(i) A homogeneous prismatic bar hangs from a ceiling verticallydownwards under its own weight. The bar has density,?,Length, L and cross-sectional area, A. Show that the total elongation of the bar is given by Eq. (1):
The brass tube AB (E= 105 GPa) has a cross-sectional area of 14 0 m m2 and is fitted with a plug at A. The tube is attached at B to a rigid plate that is itself attached at C to the bottom of an alumi-num cylinder (E= 72 GPa) with a cross-sectional area of 250 mm2. The cylinder is then hung from a support at D. In order to close the cylinder, the plug must move down through 1 mm. Determine the force P that must be applied to the cylinder.
The rigid bar AD is supported by pin connection at point F and an elastic link AB. The link AB hasthe cross-sectional area 20 mm2 and made of red brass C83400 copper alloy. If P=200 N, determine the axial deflection of the link AB.
The rigid bar AB with a length of 5m, is attached to two vertical rods and ishorizontal before the uniformly varying load of zero intensity at point A and 10kN/mat point B is applied. The rod at A is steel with L=3m, A=300 mm2 and E=200GPa. Therod in B is aluminum with L=4m, A=500mm2 and E = 70GPa. Determine the verticaldisplacement of the bar at a point where the resultant of the load is acting.
A hollow steel [E= 30,000 ksi] tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum [E= 10,000 ksi] rod (2) that has a 2-in.-diameter and a solid 1.375-in.-diameter aluminum rod (3). Determine: (a) the change in length of steel tube (1).(b) the deflection of joint D with respect to the fixed support at A.(c) the maximum normal stress in the entire axial assembly.
A square beam with a side of 7.6 cm has a density of 11,000 kg/m³ and is 2.4 m long. It is recessed and undergoes a load of 4000 N at 1.5 m from the recess. If its Young's modulus is 150 GPa, determine its deflection at the free end. Consider the weight of the beam. Answer: -2.67cm
Determine the changes in length, breadth and thickness of a steel bar which is 4 m long, 30 mm wide and 20 mm thick and is subjected to an axial pull of 30 kN in the directions of its length. Take Young’s Modulus as 70 GPa and Poisson’s ratio as 0.3.