B3. A circular plate of diameter 2.75 m is vertically placed in water in such a way that the centre of the plate is 7.4 m below the free surface of water. Find the total pressure & center pressure on the plate. Draw the diagram neatly. Total Pressure on the circular plate (in N) Centre of Pressure on the circular plate (in m)

B3. A circular plate of diameter 2.75 m is vertically placed in water in such a way that the centre of the plate is 7.4 m below the free surface of water. Find the total pressure & center pressure on the plate. Draw the diagram neatly. Total Pressure on the circular plate (in N) Centre of Pressure on the circular plate (in m)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An open cylindrical tank has a base diameter of 1.2 meter and contains 3.86 meter deep water. the tank is rotated about its vertical axis at 80 rpma. What is the maximum height of the tank so that no water will spill at 80 rpm? b. If ω = 140 MPa, what will be the pressure at the center bottom of the tank?
The pressure at a point “m” in the figure shown was increased from 70 kPa to 105 kPa. This causedthe top level of mercury to move 20 cm in the sloping tube. What is the inclination, θ?
A closed cylindrical vessel, 3 m in diameter and 4 m high is filled with water to a depth of 3m and rotated about its own vertical axis at a constant angular speed, ω. The air inside the vessel is under a pressure of 130 kPa. If ω = 13 rad/sec, what is the pressure at the center and circumference at the bottom of the tank?
Q2/A rectangular plate of AB 1.2 meter by 5-meter size is immersed in water. The plane of the plate is inclined at 45° with free water surface and the end of plate at(B) a depth of 5 meters from water surface. Find the total pressure on the plate and the position of center of pressure.
The 45 ° V-tube in Fig. contains water and is open atA and closed at C . What uniform rotation rate in r/minabout axis AB will cause the pressure to be equal at pointsB and C ? For this condition, at what point in leg BC will thepressure be a minimum?
A hollow circular plate of 3 m external diameter and 1 m internal diameter is immersed in water such that its centre is at a depth of 2.5 m from the water surface. Find the total pressure and the point where it acts.
A plate has the shape of a circle with radius 5 m. The plate is submerged vertically in water so that thebottom of the plate is 15 m below the surface of the water. Find the hydrostatic force exerted on the platedue to the hydrostatic pressure of the water.
A door in the side of a tank is 3.1 m wide and 5.2 m high, the tank is filled to the top of the door with water of density 1000kg/m3. What is the force on the door in N?
The tank in Fig. has a 4-cm-diameter plug at the bottomon the right. All fl uids are at 20 ° C. The plug will pop out if thehydrostatic force on it is 25 N. For this condition, what willbe the reading h on the mercury manometer on the left side?
A closed cylindrical vessel, 2m in diameter & 4m high is fully filled with water & rotated to its vertical axis at a constant speed of 12.2 rad/sec. The top is pressurized by 180 KPa. (a) What is the pressure at the center bottom of the cylinder? (b) What is the pressure at the circumference bottom of the cylinder? (c) What is the total hydrostatic force at the sides of the cylinder?
Gate ABC is a circular arc, sometimes called a Tainter gate ,which can be raised and lowered by pivoting about point O .See Fig.. For the position shown, determine ( a ) thehydrostatic force of the water on the gate and ( b ) its line ofaction. Does the force pass through point O ?
Piston A has a cross-section of 1,200 cm2 while that of B is 800 cm2. B is higher than A by 200cm. If the intervening passages are filled with oil and a force of PB=4.6kn is acting on B. What must be the pressure in N/m2 exerted at A?