A closed cylindrical vessel, 2m in diameter & 4m high is fully filled with water & rotated to its vertical axis at a constant speed of 12.2 rad/sec. The top is pressurized by 180 KPa. (a) What is the pressure at the center bottom of the cylinder? (b) What is the pressure at the circumference bottom of the cylinder? (c) What is the total hydrostatic force at the sides of the cylinder?

A closed cylindrical vessel, 2m in diameter & 4m high is fully filled with water & rotated to its vertical axis at a constant speed of 12.2 rad/sec. The top is pressurized by 180 KPa. (a) What is the pressure at the center bottom of the cylinder? (b) What is the pressure at the circumference bottom of the cylinder? (c) What is the total hydrostatic force at the sides of the cylinder?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Similar questions

A closed cylindrical vessel, 3 m in diameter and 4 m high is filled with water to a depth of 3m and rotated about its own vertical axis at a constant angular speed, ω. The air inside the vessel is under a pressure of 130 kPa. If ω = 13 rad/sec, what is the pressure at the center and circumference at the bottom of the tank?
Problem 3.- Blaise Pascal doubled Torricelli's barometer using Red wine, with a density of 984kg / m3 . (a) What was the height h of the wine column for normal atmospheric pressure? (b) Would you expect the emptiness on the column ti be as good as for mercury? Explain and argue.
Pc = 40, Pif = -2, πc = 20, πif = 4. (P = hydrostatic pressure, π – oncotic pressure, c – capillary, if – interstitial fluid). Calculate the direction and magnitude of the Starling forces
The cap at point B on the 5-cm-diameter tube in Fig.will be dislodged when the hydrostatic force on its basereaches 22 lbf. For what water depth h does this occur?
An open cylindrical tank has a base diameter of 1.2 meter and contains 3.86 meter deep water. the tank is rotated about its vertical axis at 80 rpma. What is the maximum height of the tank so that no water will spill at 80 rpm? b. If ω = 140 MPa, what will be the pressure at the center bottom of the tank?
What is the absolute pressure inside a water drop having radius 1mm and surface tension as 0.1 N/m? Assume atmospheric pressure as 1 bar.
The Hoover Dam, in Arizona, encloses Lake Mead,which contains 10 trillion gallons of water. The dam is1200 ft wide and the lake is 500 ft deep. ( a ) Estimate thehydrostatic force on the dam, in MN. ( b ) Explain howyou might analyze the stress in the dam due to this hydrostaticforce.
The 45 ° V-tube in Fig. contains water and is open atA and closed at C . What uniform rotation rate in r/minabout axis AB will cause the pressure to be equal at pointsB and C ? For this condition, at what point in leg BC will thepressure be a minimum?
End D of a 2.5 long uniformly plain wooden rod( s.g=0.7) is held 0.3m below the surface of still water. (a.) How much of the rod remains above the water surface? (b.) if the rod diameter is 25mm what force of D is required to hold it in place ?
A block with specific gravity of SG= 1.45 and volume V= 0.75m3, is attached to a spring scale. The block is hung vertically such that it is fully submerged in oil ρoil= 0.85kg/m3 . a) Draw a free body diagram for the block. b) What is the apparent weight of the block?
3. Supposed that air (std.) has a uniform density of 1.2kg/m^3, estimate how high (meters) above the sea level where there exists a zero pressure. Assume that in the given condition, barometric pressure at sea level is 101.325 kPa. Include also the free body diagram or figure of the problem, and your findings after solving it.
The 6-ft-radius waterwheel in Fig. is being used tolift water with its 1-ft-diameter half-cylinder blades. If thewheel rotates at 10 r/min and rigid-body motion is assumed,what is the water surface angle θ at position A ?